The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG964-07E Demonstation Board has everything you need to evaluate
the remarkable ASR022-10E ABZ TMR Encoder Sensor. The demonstration includes:
ASR022-10E ABZ Noncontact TMR Encoder Sensor
A four-digit display to indicate rotation
Part # 12426 split-pole Alnico 5 round horseshoe magnet
LEDs for A, B, Z, and Direction outputs
Plastic magnet locating fixture
Powered by two AAA batteries (included)
$195.00
The IL4622 is an isolated, full-duplex 40 Mbps 3.3-volt bus RS-422 / RS-485 transceiver with an integrated 3.3V-to-3.3V DC-DC convertor.
The transceiver runs up to 40 Mbps, has a 1/5 Unit Load.
The DC-DC convertor can output up to 80 mA and is fully regulated.
2500 VRMS isolation; 16.5 kV bus ESD protection; 16-pin wide-body SOIC package with True 8™ mm creepage.
$9.31
ASR022 noncontact TMR encoder sensors provide precise pulses indicating angular motion, and is more accurate and smaller than other non-contact encoders.
An ABZ interface allows the ASR022 to replace legacy optical encoders.
The sensor combines precise, low-power Tunneling Magnetoresistance (TMR) sensing elements with sophisticated digital signal processing.
The sensor is factory calibrated, with coefficients stored in internal memory.
The ASR022 is designed for harsh industrial or automotive environments with ESD protection, and full −40 °C to 125 °C operating temperature range.
$8.98
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL611CMTI-1E is a two-channel version in an ultramniature MSOP8 package.
$6.23
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL610CMTI-3E is a single-channel version in a SOIC8 package.
$3.84
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL610CMTI-1E is a single-channel version in an ultraminiature MSOP8 package.
$3.84
The AG963-07E Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR012-10E I2C Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR012-10E sensor
- a diametrical
magnet
- magnet fixturing
An interface board with:
- a microcontroller
connected to the sensor via I²C
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
$195.00
ASR012 TMR Smart Angle Sensors provide a precise digital indication of magnetic rotation operating over a wide range of speeds.
The sensor combines a precise, low-power Tunneling Magnetoresistance (TMR) sensor with sophisticated digital signal processing.
The ASR012 provides an extraordinary combination of speed and precision, with a 12.5 kSps sample rate and ±0.2° repeatability.
The sensor is factory calibrated, with coefficients stored in
internal memory.
An I²C interface provides angle data and allows
setting device parameters. A PWM output is also provided
The ASR012 is designed for harsh industrial or automotive environments with ESD protection and full −40°C to +125°C operating temperature range.
$8.98
This Evaluation Board uses the 3.3-to-3.3V version of the world’s smallest isolated DC-to-DC convertor, the ILDC11-15E.
The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC11-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.
The ILDC11 is an ultraminiature one-quarter watt DC-to-DC convertor with 2.5 kV isolation that can be used to generate an isolated 3.3-volt bus supply from a 3.3-volt controller supply.
No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
$49.95
This board implements a complete isolated 5-volt RS-485 node using an IL2985E low-power transceiver, an ILDC11-15E ultraminiature isolated DC-DC convertor, and a commodity boost regulator.
The
4 by 3 inch (100 by 75 mm) board provides screw terminal and test point connections.
The IL2985E is a low-power, fully-isolated, differential 5-volt bus transceiver. The ILDC11-15E isolates the 3.3-volt controller supply, and a boost regulator provides a fully-isolated five-volt bus supply.
$84.95
This Evaluation Board provides a complete isolated 3.3-volt RS-485 node using an IL3685PE isolated transceiver and an ILDC11-15E ultraminiature isolated DC-DC convertor. The 4 by 3 inch (100 by 75 mm) board provides screw terminal and test point connections.
The IL3685PE is a high-speed, fully-isolated, differential 3.3-volt bus transceiver.
The ILDC11-15E 3.3-to-3.3 volt DC-DC convertor provides a fully-isolated 3.3-volt bus supply using the controller supply.
$84.95
This Evaluation Board is a complete isolated RS-485 / RS-422 node using the IL4622E isolated transceiver with integrated isolated DC-DC convertor.
The 4 by 3 inch (100 x 75 mm) board provides screw terminal and test point connections, and uses a 2s2p board with thermal vias for optimal thermal performance.
The IL4622E is a high-speed, fully-isolated, full duplex differential bus transceiver with an integrated
3.3-to-3.3 volt DC-DC convertor to provide a fully-isolated 3.3 volt bus supply using the controller supply. This level of integration dramatically reduces chip count and board area.
$84.95
The ILDC11-15E is a one-quarter watt fully-regulated 3.3V-to-3.3V DC-DC convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate an isolated 3.3-volt bus supply from a controller supply.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide full 2.5 kV isolation and virtually unlimited barrier life.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
$5.43
NVE's ADT925-14E Nanopower Switch integrates GMR sensor elements with digital signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: 1.5 mT (15 Oe) Digital Switch Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V 1 microamp quiescent current at 3 V without duty-cycling 20 kHz switching frequency Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package Applications: Battery-Powered Devices Portable Instruments Wearables
$5.67
NVE's ADT924-14E Nanopower Switch integrates GMR sensor elements with digital signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: 2.2 mT (22 Oe) Digital Switch Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V 1 microamp quiescent current at 3 V without duty-cycling 20 kHz switching frequency Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package Applications: Battery-Powered Devices Portable Instruments Wearables
$5.67
The IL4685 is an isolated 40 Mbps 3.3-volt bus RS-485 transceiver with an integrated 3.3V-to-3.3V DC-DC convertor.
The transceiver runs up to 40 Mbps, has a 1/5 Unit Load.
The DC-DC convertor can output up to 80 mA and is fully regulated.
2500 VRMS isolation; 16.5 kV bus ESD protection; 16-pin wide-body SOIC package with True 8™ mm creepage.
$9.31
The unique AHK991-14E is a high-field, low voltage, low power, TMR magnetic switch, designed for MRI detection in implantable medical devices.
The sensors have a 350 mT (3500 Oe) typical operate point, which is high enough to detect MRI fields or strong, rare-earth magnets in close proximity. Such high fields disrupt most other magnetic sensors.
The sensors can withstand unlimited fields without
being damaged or turning off.
Unlike Hall effect or other sensors, the switch is sensitive to magnetic fields in any direction.
Key Specifications:
350 mT operate point
0.9 to 1.8 V
2 µA typical supply current
3000 Hz switching speed
-40 to 85°C
$17.05
The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM125-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00