The IL3685 is an isolated 40 Mbps RS-485 transceiver with an extended temperature range. Over-temperature protection; fully PROFIBUS compliant; 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
This part is lead (Pb) free.
Lead-free
product information
$5.51
The IL3085TE is an isolated 4 Mbps RS-485 transceiver with an extended temperature range. Compatible with 3.3 V or 5 V input logic. 16-pin wide-body SOIC package with True 8™ mm creepage.
$5.05
This Arduino Shield board implements an H-bridge power converter using four power MOSFETs, four IL610CMTI-1E
ultrahigh CMTI isolated MOSFET drivers, and two ILDC13-15E ultraminiature isolated DC-to-DC convertors.
The board is rated for 40 volts and 50 amps, to control
up to two-kilowatt loads.
Example programs are available via our GitHub Repository.
Key features of the board are:
• A Simple three-wire Arduino interface (PWM, Dir, and Enable)
• Heat-sinking and thermal vias
• Standard Arduino Shield form factor outline
• Easy connections with large screw terminals
Specifications:
• Max. load: 2 kW (40 V / 50 A)
• Load supply line: 8 to 40 V
• Arduino input supply: 5V or 7 V to 20 V, 500 mA max.
• Logic-to-load isolation: 2.5 kV per UL 1577
• Operating Temperature Range: -40 °C to 85 °C
• Dimensions: 2.1 in. by 2.7 in. (53.4 mm by 68.6 mm)
Applications:
• Motor speed and direction control
• Robotics
• DC-to-AC invertors
$195.95
This Evaluation Board provides a complete isolated four-channel SPI node, plus isolated power, using an IL7817VE.
The four- by three-inch (100 mm by 75 mm) board provides screw terminals for connections, plus test points for checking voltages and I/O. There are also LEDs to indicate DC-to-DC convertor input and output power. It uses a 2s2p board with thermal vias for optimal thermal performance.
The IL7817V is a high-speed, fully-isolated, data couplers with an integrated, one-quarter watt DC-to-DC convertor. This level of integration dramatically reduces chip count and board area.
$84.95
This Evaluation Board uses the 3.3-to-6 V version of our miniature DC-to-DC convertor, the ILDC13VE.
The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC13VE plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.
The ILDC13VE is an miniature one-quarter watt DC-to-DC boost convertor with 4 kV isolation that can be used to generate an isolated six-volt gate supply from a 3.3-volt controller supply.
No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
$49.95
This Evaluation Board uses the 3.3-to-5 V version of our miniature DC-to-DC convertor, the ILDC12VE.
The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12VE plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.
The ILDC12 is an ultraminiature one-quarter watt DC-to-DC boost convertor with 4 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.
No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
$49.95
This Evaluation Board uses the 3.3-to-3.3V version of our miniature DC-DC convertor, the ILDC11VE.
The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC11-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.
The ILDC11VE is a miniature one-quarter watt DC-to-DC convertor with 4 kV isolation that can generate an isolated 3.3-volt bus supply from a 3.3-volt controller supply.
No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
$49.95
This Evaluation Board uses the 3.3-to-6 V version of the world’s smallest isolated DC-to-DC convertor, the ILDC13-15E.
The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC13-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.
The ILDC13-15E is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated six-volt gate supply from a 3.3-volt controller supply.
No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
$49.95
This Evaluation Board uses the 3.3-to-5 V version of world’s smallest isolated DC-to-DC convertor, the ILDC12-15E.
The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.
The ILDC12 is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.
No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
$49.95
The ALT021 is an ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor. The differential bridge
output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity.
Features:
±0.25 mT linear range
Ultrahigh sensitivity (500 mV/V/mT typical)
Large output signal (200 mV/V/mT typical)
0 - 10 V power supply
Wheatstone bridge magnetometer configuration
20 kiloohm device resistance for low power
Up to 300 kHz frequency bandwidth
2.5 x 2.5 mm TDFN6 package
–40 to 125°C
Applications:
Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
Navigation
$12.00
ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.
The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.
To minimize power, the ADT005 does not include
the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.
The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.
The sensors are typically used with
radially-magnetized disk magnets or split pole magnet.
An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
$10.61
The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$2.25
The IL7816VE is a four-channel (two each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$12.40
The IL7817VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$12.40
The IL7815VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$12.40
The IL7814VE is a three-channel (2 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$11.78
The IL7812VE is a two-channel (one each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$11.16
The IL7811VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$11.16
The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 4 kV isolation and virtually unlimited barrier life.
The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
$5.43
The ILDC12-15E is a one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide full 2.5 kV isolation and virtually unlimited barrier life.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
$5.43