New Products

Displaying 81 to 100 (of 434 products)
ALT021-10E: 0-0.25 mT TMR Bipolar Analog Sensor, 20 KOhm, x-axis, TDFN6

The ALT021 is an ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. Features: ±0.25 mT linear range Ultrahigh sensitivity (500 mV/V/mT typical) Large output signal (200 mV/V/mT typical) 0 - 10 V power supply Wheatstone bridge magnetometer configuration 20 kiloohm device resistance for low power Up to 300 kHz frequency bandwidth 2.5 x 2.5 mm TDFN6 package –40 to 125°C Applications: Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
Navigation

Part Number:
ALT021-10E
Quantity in Stock:
9428

$12.00

ADT005-10E: High Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6

ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.

The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.

To minimize power, the ADT005 does not include the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.

The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.

The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.

Part Number:
ADT005-10E

$11.18

AG957-06E: Bare breakout board for ASR0xx Smart Angle Sensors

The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG957-06E
Quantity in Stock:
11

$2.25

IL7816VE: 4-channel (2 each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7816VE is a four-channel (two each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7816VE
Quantity in Stock:
22

$12.40

IL7817VE: 4-channel (3 transmit, 1 receive) Isolator w/3.3-5V DC-DC Convertor

The IL7817VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7817VE

$12.40

IL7815VE: 4-channel (all same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7815VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7815VE
Quantity in Stock:
9

$12.40

IL7814VE: 3-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7814VE is a three-channel (2 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7814VE
Quantity in Stock:
16

$11.78

IL7812VE: Two-channel (one each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7812VE is a two-channel (one each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7812VE
Quantity in Stock:
18

$11.16

IL7811VE: Two-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7811VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7811VE

$11.16

ILDC12VE: 6 kV Isolation 1/4W 3.3-to-5V DC-DC Conv Wide SOIC

The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 6 kV isolation and virtually unlimited barrier life.

The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC12VE

$5.98

ILDC12-15E: Isolated 1/4W 3.3-to-5V DC-DC Conv, 1kV, DFN6

The ILDC12-15E is a one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide 1 kV isolation and virtually unlimited barrier life.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC12-15E

$5.43

ILDC13VE: 6 kV Isolation 1/4W 3.3-to-6V DC-DC Conv Wide SOIC

The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor. The part can be used to generate isolated high-side gate supplies for H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 6 kV isolation and virtually unlimited barrier life.

The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC13VE

$5.98

ILDC13-15E: Isolated 1/4W 3.3-to-6V DC-DC Conv, 1 kV, DFN6

The ILDC13-15E is a one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated high-side gate supplies for H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide 1 kV isolation and virtually unlimited barrier life.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC13-15E

$5.43

AG973-07E: SM223-10E Smart I²C TMR Magnetometer Evaluation Kit

The AG973-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM228-10E sensor.
          - a microcontroller connected to the sensor via I2C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • An LED indicating the state of the threshold output.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG973-07E
Quantity in Stock:
7

$95.00

AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board

The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG975-07E

$19.95

AG974-07E: ACT001-10E Isolated Current Sensor Evaluation Board

This 2” x 2” square evaluation board allows you to test the remarkable ACT001-10E current sensor and a common application circuit.

The ACT001-10E is a fully-isolated, inline current sensor with an on-chip current strap. A Wheatstone bridge manufactured with NVE’s state-of-the-art tunneling magnetoresistance (TMR) sensor elements detects the magnetic field from the input current across NVE’s unique polymer isolation barrier.

Part Number:
AG974-07E
Quantity in Stock:
13

$50.00

IL810T-3E: Single Channel Top-of-the-Line Isolator, 2.5 kV, SOIC8

The IL810T-3E is NVE's top-of-the-line single-channel isolator, with best-in-class specifications:
• 125 °C max. operating temperature
• 110 Mbps
• 10 ns propagation delay
• DC-correct; deterministic power-up
• 50 kV/µs typ.; 30 kV/µs min. transient immunity
• IEC 60747-5-5 (VDE 0884) certified—600 Vrms WV
• 44000-year barrier life
• Low EMC footprint

The part is an 8-pin SOIC RoHS package.

Part Number:
IL810T-3E
Quantity in Stock:
1315

$3.93

SM223-10E: High-Speed Smart TMR Magnetometer, 1.5mT, I2C, TDFN6

The SM223-10E Smart Magnetometer combines a Tunneling Magnetoresistance (TMR) sensor element with sophisticated digital signal processing for a unique combination of speed and precision. An I2C interface provides data as well as an external programming interface, and allows setting a versatile digital threshold output.

Unlike awkward, old-fashioned Hall-effect sensors, TMR is sensitive in-plane for optimal current sensing and easy mechanical interfaces. Key features include:
  •  0 to 1.5 mT linear range
  •  Can detect magnets more than 150 mm away
  •  Simple I2C interface
  •  Programmable digital threshold output
  •  2% of full-scale accuracy for 0 to 125°C
  •  Fast 10000 sample-per-second update rate
  •  Factory calibrated
  •  Programmable offset and gain compensation
  •  -40°C to +125°C operating range
  •  Ultraminiature 2.5 x 2.5 mm DFN6 package

Part Number:
SM223-10E
Quantity in Stock:
5

$6.88

IL860-1E: 5-Channel (all same direction) Top-of-the-Line Isolator, 2.5 kV, QSOP

The IL860-1E is NVE's top-of-the-line five-channel isolator, with best-in-class specifications:
• 110 Mbps
• 10 ns propagation delay
• DC-correct; deterministic power-up
• 50 kV/µs typ.; 30 kV/µs min. transient immunity
• 125 °C max. operating temperature
• 44000-year barrier life
• Low EMC footprint

The part uses NVE's 16-pin QSOP package. The "E" suffix indicates this part is lead (Pb) free.

Part Number:
IL860-1E
Quantity in Stock:
493

$9.40

IL4822E: Isolated RS422 Transceiver w/3.3-5V DC-DC Convertor, 2.5 kV, Wide SOIC

The IL4822 is an isolated, full-duplex 40 Mbps 5-volt bus RS-422 / RS-485 transceiver with an integrated 3.3V-to-5V DC-DC convertor.

The transceiver runs up to 40 Mbps, has a 1/5 Unit Load.

The DC-DC convertor can output up to 50 mA and is fully regulated.

2500 VRMS isolation; 16.5 kV bus ESD protection; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL4822E
Quantity in Stock:
806

$9.32

Displaying 81 to 100 (of 434 products)