New Products

Displaying 41 to 60 (of 408 products)
ILDC12-01: Ultraminiature Isolated 3.3-to-5V DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-5 V version of world’s smallest isolated DC-to-DC convertor, the ILDC12-15E.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC12 is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC12-01

$49.95

ALT021-10E: 0-0.25 mT TMR Bipolar Analog Sensor, 20 KOhm, x-axis, TDFN6

The ALT021 is an ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. Features: ±0.25 mT linear range Ultrahigh sensitivity (500 mV/V/mT typical) Large output signal (200 mV/V/mT typical) 0 - 10 V power supply Wheatstone bridge magnetometer configuration 20 kiloohm device resistance for low power Up to 300 kHz frequency bandwidth 2.5 x 2.5 mm TDFN6 package –40 to 125°C Applications: Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
Navigation

Part Number:
ALT021-10E
Quantity in Stock:
9536

$12.00

ADT005-10E: High Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6

ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.

The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.

To minimize power, the ADT005 does not include the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.

The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.

The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.

Part Number:
ADT005-10E
Quantity in Stock:
175200

$11.18

AG957-06E: Bare breakout board for ASR0xx Smart Angle Sensors

The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG957-06E
Quantity in Stock:
11

$2.25

IL7816VE: 4-channel (2 each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7816VE is a four-channel (two each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7816VE
Quantity in Stock:
22

$12.40

IL7817VE: 4-channel (3 transmit, 1 receive) Isolator w/3.3-5V DC-DC Convertor

The IL7817VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7817VE
Quantity in Stock:
1

$12.40

IL7815VE: 4-channel (all same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7815VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7815VE
Quantity in Stock:
9

$12.40

IL7814VE: 3-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7814VE is a three-channel (2 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7814VE
Quantity in Stock:
16

$11.78

IL7812VE: Two-channel (one each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7812VE is a two-channel (one each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7812VE
Quantity in Stock:
18

$11.16

IL7811VE: Two-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7811VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7811VE

$11.16

ILDC12VE: 4 kV Isolation 1/4W 3.3-to-5V DC-DC Conv Wide SOIC

The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 4 kV isolation and virtually unlimited barrier life.

The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC12VE
Quantity in Stock:
3

$5.98

ILDC12-15E: Isolated 1/4W 3.3-to-5V DC-DC Conv, 1kV, DFN6

The ILDC12-15E is a one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide 1 kV isolation and virtually unlimited barrier life.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC12-15E

$5.43

ILDC13VE: 4 kV Isolation 1/4W 3.3-to-6V DC-DC Conv Wide SOIC

The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor. The part can be used to generate isolated high-side gate supplies for H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 4 kV isolation and virtually unlimited barrier life.

The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC13VE

$5.98

ILDC13-15E: Isolated 1/4W 3.3-to-6V DC-DC Conv, 1 kV, DFN6

The ILDC13-15E is a one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated high-side gate supplies for H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide 1 kV isolation and virtually unlimited barrier life.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC13-15E

$5.43

AG976-07E: ASR003-10E Smart SPI Angle Sensor Evaluation Kit

The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.

Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.

Part Number:
AG976-07E

$195.00

AG977-07E: ASR003 Smart TMR Angle Sensor breakout board

The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG977-07E
Quantity in Stock:
4

$19.95

AG973-07E: SM223-10E Smart I²C TMR Magnetometer Evaluation Kit

The AG973-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM228-10E sensor.
          - a microcontroller connected to the sensor via I2C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • An LED indicating the state of the threshold output.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG973-07E
Quantity in Stock:
7

$95.00

AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board

The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG975-07E

$19.95

AG974-07E: ACT001-10E Isolated Current Sensor Evaluation Board

This 2” x 2” square evaluation board allows you to test the remarkable ACT001-10E current sensor and a common application circuit.

The ACT001-10E is a fully-isolated, inline current sensor with an on-chip current strap. A Wheatstone bridge manufactured with NVE’s state-of-the-art tunneling magnetoresistance (TMR) sensor elements detects the magnetic field from the input current across NVE’s unique polymer isolation barrier.

Part Number:
AG974-07E
Quantity in Stock:
20

$50.00

AAH002-02E PCBA: Ultrahigh Sensitivity Analog Sensor Assembly

A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.

Part Number:
AAH002-02E PCBA
Quantity in Stock:
27

$150.00

Displaying 41 to 60 (of 408 products)