The IL260-3E is a 3.3/5.0-volt, 5-channel isolated, 110 Mbps, CMOS-compatible logic buffers with 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin, narrow-body (0.15"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL3085-3 is a cost-effective isolated 4 Mbps RS-485 transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin narrow-body (0.15''-wide) SOIC package (Pb-free).
AB001-00E GMR Gradient Sensors (Gradiometers) offer unparalleled magnetic gradient
sensing. Two pairs of unshielded GMR bridge resistors provide directional sensing
of small gradients over a wide range of magnetic field strength. The devices
are sensitive only to gradients, and have low sensitivity to constant magnetic
noise.
Differential magnetic field sensor (gradiometer) -- for gear tooth, multi-pole magnet, and high noise rejection sensing.
Typ. Min. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
250
20 - 200
0.02 - 0.03
2,500 +/-20%
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) when purchasing quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
AAT009-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology for ultralow power, high output signal, and a wide airgap tolerance. Sine and cosine outputs provide
full quadrature. The AAT009-10E version has the highest device resistance in the AAT product family (6 megaohms typ.), for the lowest power consumption.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op. Temp.
Typ. Device
Resistance
Package
200 mV/V
30 Oe
0.5 degrees
125°C
6 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
The IL715 is a 3.3/5V, multichannel isolated CMOS-compatible logic buffers with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
NVE's ABL015-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.5 mm apart on the sensor IC, and the two sensors are phase shifted by 0.25 mm.
Bridge Resistance for Each Bridge (Ohms)
Linear Range (Oersteds)
Output
Comments
Package
Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm, and phase shift from sensor to sensor is 0.250 mm.
4K - 7K
+/-5 to +/-100
Dual Analog Bridge
Gear Tooth or Encoder
MSOP8
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The 12217 magnet is a round, 3.5 mm dia. x 4 mm thick Y25 ferrite disk magnet. Typical field strength is 1700 Oe at the magnet face.
This magnet is also included in the AG920-07
Gear Tooth Sensor Evaluation Kit.
The IL3585 is an isolated 40 Mbps RS-485 transceiver and is compatible with 3.3 V or 5 V input logic. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
This part is lead (Pb) free.
Lead-free
product information
The IL717T-3 is a high temperature 3.3/5V, multi-channel, isolated, 110 Mbps, CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin narrow-body (0.15"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL710T-2 is a high temperature, 3.3/5V, single channel, 110 Mbps, CMOS compatible, isolated buffer with automatic level shifting, output enable, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin PDIP package.
The "E" suffix indicates this part is lead (Pb) free.
AAT003-10E
Angle Sensors use Tunneling Magnetoresistance (TMR) technology to produce a very
high output signal without amplification, a wide airgap tolerance, and low power. Sine and cosine outputs provide full quadrature. The sensor has a 40 kilohm device
resistance and 20 kilohm output impedance, which is ideal for direct interface to microcontrollers.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op. Temp.
Typ. Device
Resistance
Package
200 mV/V
30 Oe
0.5 degrees
125°C
40 kΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
The IL485W performs the same EIA-485 and PROFIBUS functions as the IL485, but has an additional uncommitted isolation channel which is useful for fault detection in bus contention situations.
The "E" suffix indicates this part is lead (Pb) free.
The IL262E is a 3.3/5.0-volt, 5-channel (3 transmit; 2 receive) isolated, 110 MBaud CMOS compatible logic buffers with 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL710T-3 is a high temperature, 3.3/5V, single channel, 110 Mbps, CMOS compatible, isolated buffer with automatic level shifting, output enable, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
ABH001-00E GMR Gradient Sensors (Gradiometers) offer unparalleled magnetic gradient sensing. Two pairs of unshielded GMR bridge resistors provide directional sensing of small gradients over a wide range of magnetic field strength. The devices are sensitive only to gradients with low sensitivity to constant external magnetic noise. This allows these sensors to operate in high noise environments, such as near electric motors or high-current wires.
Key Features:
Extremely High Sensitivity to Applied Magnetic Fields
Wheatstone Bridge Analog Output
Temperature to 150 degrees Continuous
Wide Linear Range of Operation
Near-Zero Voltage Operation
DC to >1MHz Frequency Response
MSOP Package
Applications:
General Differential Field Sensing
Gear Tooth and Encoder Speed and Position Sensing
Low Voltage, High Temperature Applications
Differential magnetic field sensor (gradiometer) --
for gear tooth, multi-pole magnet, and high noise rejection sensing.
Typ. Min. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Resistor
Sensitivity
(%R/Oe)
min.-max.
Resistance
(Ohms)
Package
70
5 - 40
0.06 - 0.12
1,200 +/-20%
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) when purchasing quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
The IL41050TFD-1E is an ultraminiature isolated CAN FD transceiver with no performance compromises. 125C; 5 Mbps; 3.3 V or 5.0 V input logic.
16-pin QSOP package--the world's smallest isolated transceiver.
Features include 3.3 V or 5.0 V input logic, 15 kV bus ESD protection, 5 Mbps data rate, and 20 kV per microsecond transient immunity. 16-pin wide-body (0.3'') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The IL721VE is a 6 kVrms isolation, 125C, 3.3/5V, two channel, isolated, 110 Mbps, CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, and 50 kV/microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
The "E" suffix indicates this part is lead (Pb) free.
NVE's AD221-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 20 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
15-25
5
0.4
Sink/Source
FBB
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.