The IL41050TAE is a high-speed, low-power isolated ISO 11898 compliant CAN transceiver. 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic.
16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
NVE's ADL124-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package
2.4 to 4.2 V
Typical Power Consumption 72 nW at 2.4 V
30 Hz Typical Update Frequency
Digital Switch Output
Integrated Duty-Cycling
Applications:
Battery-Powered Devices
Portable Instruments
The IL716-3 is a 3.3/5V, multichannel isolated 110 Mbps CMOS-compatible logic buffers with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin narrow-body (0.15"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
NVE's AD005-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 40 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
ADT001-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.
An additional output indicates a fault if the magnetic field is too high.
The ADT001 is high hysteresis for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.
The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.
The sensors are typically used with
radially-magnetized disk magnets or split pole magnet.
An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
Features include 3.3 V or 5.0 V input logic, 15 kV bus ESD protection, 5 Mbps data rate, and 20 kV per microsecond transient immunity. 16-pin narrow-body (0.15'') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
NVE's AHL921-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing. The Nanopower Switch is extremely small and low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
35 Microamps Typical Supply Current
110 Hz Typical Update Frequency
Digital Switch Output
Applications:
Battery-Powered Devices
Portable Instruments
NVE's ABL005-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.5 mm apart on the sensor IC arranged in a full bridge configuration.
Bridge Resistance (Ohms)
Linear Range (Oersteds)
Output
Comments
Package
Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm.
4K - 7K
+/-5 to +/-100
Analog Bridge
Gear Tooth or Encoder
MSOP8
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The IL712-2 is a 3.3/5V dual-channel bidirectional 110 Mbps CMOS-compatible isolated buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin PDIP package.
The "E" suffix indicates this part is lead (Pb) free.
The ALT021 is an ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor. The differential bridge
output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity.
Features:
±0.25 mT linear range
Ultrahigh sensitivity (500 mV/V/mT typical)
Large output signal (200 mV/V/mT typical)
0 - 10 V power supply
Wheatstone bridge magnetometer configuration
20 kiloohm device resistance for low power
Up to 300 kHz frequency bandwidth
2.5 x 2.5 mm TDFN6 package
–40 to 125°C
Applications:
Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
Navigation
The IL711-2 is a 3.3/5V, dual-channel unidirectional 110 Mbps CMOS compatible isolated buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin PDIP package.
The "E" suffix indicates this part is lead (Pb) free.
The IL3522VE is a 6 kVrms isolated, high-speed differential bus transceiver, designed for bidirectional data communications on balanced transmission lines. The IL3522 offers an exceptional 2.3 V differential output into a 54 ohm load, over the supply range of 4.5 V to 5.5 V. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
This part is lead (Pb) free.
Lead-free
product information
Isolated 1/8 fractional load RS485 transceiver compatible with 3.3 V or 5.0 V input logic. Additional features include 15 kV bus ESD protection, 5 Mbps data rate, and 20 kV per microsecond transient immunity. 16-pin wide-body (0.3') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The IL611-3E is a 3.3/5V, dual-channel, 100 Mbps isolated signal coupler with CMOS outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged couplers).
This part is lead (Pb) free.
Lead-free
product information
The IL3585-3 is an isolated 40 Mbps RS-485 transceiver and is compatible with 3.3 V or 5 V input logic. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin narrow-body (0.15''-wide) SOIC package.
This part is lead (Pb) free.
Lead-free
product information
NVE's ABL006-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.3 mm apart on the sensor IC arranged in a full bridge configuration.
Bridge Resistance (Ohms)
Linear Range (Oersteds)
Output
Comments
Package
Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.300 mm.
4K - 7K
+/-5 to +/-100
Analog Bridge
Gear Tooth or Encoder
TDFN6
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
Up to 20 Mpbs, 3.3 V or 5.0 V input logic, 15 kV bus ESD protection, and 20 kV per microsecond transient immunity. 16-pin narrow-body (0.15'') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
NVE's AA003-02E Normalized Output GMR Magnetic Field Sensors have a unique ability
to sense static fields and offer unmatched magnetic sensitivity.
General purpose magnetometer --
senses fields from permanent magnets, earth, and current sources.
Typ. Min. Saturation Field (Oe)
Sensitivity (mV/V/Oe)
Output
Comments
Package
20
2.0 - 3.2
Analog Bridge
Low-Field Measurement
SOIC8 (RoHS)
Note: Parts must be purchased in tube multiples (increments of 92) when purchasing quantities of 92 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
The IL3685 is a 6 kVrms isolated 40 Mbps RS-485 transceiver that is fully PROFIBUS compliant. 3.3 V or 5 V input logic. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
This part is lead (Pb) free.