These 2 x 3.5-inch (50 x 90 mm) boards have an IL712-3E two channel (one each direction) high-speed isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The boards let you evaluate the world's best isolators.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
NVE's AD320-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
GBK
Std. axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL611CMTI-1E is a two-channel version in an ultramniature MSOP8 package.
NVE's AD724-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Regulated Voltage Output
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Sink/
Sink/
Vreg
LBF
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL260-1E ultraminiature five-channel (all the same direction) QSOP isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The board lets you evaluate the world's smallest high-performance isolators.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL261-1E ultraminiature five-channel (four transmit, one receive) QSOP isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The board lets you evaluate the world's smallest high-performance isolators.
The RS-485 QSOP Isolated Transceiver Evaluation Board provides a complete isolated RS-485 node using the world's isolated transceiver, the IL3085-1E. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
The RS-485 Wide-Body Isolator Evaluation Board provides a complete isolated RS-485 node using the popular 0.3" (8 mm) creepage IL3585E isolated transceiver. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
The RS-485 Narrow-Body Isolated Transceiver Evaluation Board provides a complete isolated RS-485 node using the unique 0.15"-wide IL3585-3E isolated transceiver. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
The PROFIBUS Isolated Transceiver Evaluation Board provides a complete isolated PROFIBUS node using the unique 0.15" narrow-body IL3685-3E isolated transceiver. The board provides screw terminal and PROFIBUS DB9 connections.
Termination, pull-up, and pull-down resistors are typical PROFIBUS values, and easily changed for specific applications.
The transceiver provides data rates to 40 Mbps, and is fully PROFIBUS compatible, including the stringent bus differential specifications.
These 2 x 3.5-inch (50 x 90 mm) boards include an IL3685TE isolated RS-485 transceiver,
a termination resistors, power-supply bypass capacitors as recommended, screw
connections, provisions for header pins, and a DB9 bus connector for PROFIBUS.
The IL3685TE is the world's fastest isolated transceiver with data rates to 40 Mbps, is fully PROFIBUS compatible, including the stringent bus differential specifications, and is rated to a full 125C.
The CAN Evaluation Board provides a complete isolated Controller Area Network node using the popular IL41050TA-3E isolated narrow-body isolated CAN transceiver.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
The QSOP isolated CAN Evaluation Board provides a complete isolated Controller Area Network node using the world's smallest isolated CAN transceiver, the IL41050TA-1E.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
The isolated CAN FD Evaluation Board provides a complete isolated Controller Area Network node using the world's smallest isolated CAN FD transceiver, the IL41050TFD-1E.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, pull-up resistors, and a jumper to select normal or silent mode.
This board provides a complete isolated Controller Area Network node using NVE's IL41050TTE isolated wide-body basic CAN transceiver.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
The isolated CAN Evaluation Board provides a complete isolated Controller Area Network node using NVE's popular IL41050TAE isolated wide-body CAN transceiver with true 8mm creepage.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
This Evaluation Board is a complete isolated RS-485 / RS-422 node using the IL4622E isolated transceiver with integrated isolated DC-DC convertor.
These 2 x 3.5-inch (50 x 90 mm) boards include screw terminals and test pads. LEDs indicate DC-to-DC convertor input and output power. A 2s2p board with vias optimizes thermal performance.
The IL4622E is a high-speed, fully-isolated, full duplex differential bus transceiver with an integrated
3.3-to-3.3 volt DC-DC convertor to provide a fully-isolated 3.3 volt bus supply using the controller supply. This level of integration dramatically reduces chip count and board area.