AAT001-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology to produce
a very high output signal without amplification, a wide airgap tolerance, and
very high device resistance for extremely low power. Sine and cosine outputs provide
full quadrature.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op. Temp.
Typ. Device
Resistance
Package
200 mV/V
30 Oe
0.5 degrees
125°C
1.25 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
NVE's AHL025-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
95 nA Typical Supply Current
110 Hz Typical Update Frequency
Digital Switch Output
Integrated Duty-Cycle Operation
Applications:
Battery-Powered Devices
Portable Instruments
The IL710-3 is a 3.3V/5V, single-channel, 110 Mbps CMOS-compatible isolated buffer, with enable, 10 ns propagation delay, 3 ns pulse width distortion with 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
NVE's AD024-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
BBF
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
NVE's ADL921-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing. Continuous operation allows high frequency operation. The part is packaged in an ultraminiature ULLGA.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package
2.4 V to 4.2 V
Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling
250 kHz Operating Frequency
Digital Switch Output
Applications:
Battery-Powered Devices
Portable Instruments
The IL41050TTVE is a low-cost, 5 kV basic CAN transceiver without Vref output and silent mode input pins. 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic.
16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
The IL717-3 is a 3.3/5V, multi-channel isolated 110 Mbps CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin narrow-body (0.15"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL3685 is an isolated 40 Mbps RS-485 transceiver that is fully PROFIBUS compliant. 3.3 V or 5 V input logic. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.
The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.
To minimize power, the ADT005 does not include
the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.
The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.
The sensors are typically used with
radially-magnetized disk magnets or split pole magnet.
An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
NVE's AHL024-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
95 nA Typical Supply Current
110 Hz Typical Update Frequency
Digital Switch Output
Integrated Duty-Cycle Operation
Applications:
Battery-Powered Devices
Portable Instruments
NVE's AHL924-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing. The Nanopower Switch is extremely small and low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
35 Microamps Typical Supply Current
Digital Switch Output
Applications:
Battery-Powered Devices
Portable Instruments
NVE's AHL023-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
95 nA Typical Supply Current
110 Hz Typical Update Frequency
Digital Switch Output
Integrated Duty-Cycle Operation
Applications:
Battery-Powered Devices
Portable Instruments
The IL711-3 is a 3.3/5V dual-channel unidirectional 110 Mbaud CMOS-compatible isolated buffer with 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
NVE's AHL021-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
95 nA Typical Supply Current
110 Hz Typical Update Frequency
Digital Switch Output
Integrated Duty-Cycle Operation
Applications:
Battery-Powered Devices
Portable Instruments
The IL514 is a 3.3V/5V, multichannel 2 Mbps DC-correct digital isolator, 25 ns propagation delay, 10 ns pulse width distortion with 2500 Vrms isolation and 20 kV/microsecond transient immunity, -40°C to 85°C. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
ADT002-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.
The ADT002 is lower hysteresis than the ADT005 to provide accurate, absolute rotational quadrant information.
The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.
The sensors are typically used with
radially-magnetized disk magnets or split pole magnet.
An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
NVE's AD024-10 GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Ultra-miniature 2.5 mm x 2.5 mm TDFN Package
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
BBL
Cross axis
TDFN6 (RoHS)
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
NVE's ADV001-00E is a GMR Digital Switch using a bipolar output GMR material.
This material allows the sensor to maintain an operate point with the application
of a negative (South) magnetic field, and a release point with the application
of a positive (North) magnetic field. The part is ideal for use with magnetic
encoders that have alternating North/South poles, or in any other application
where one polarity of field is required to turn the part on, and the opposite
polarity is required to turn it off.
Features:
Bipolar Operation (south field ON, north field OFF)
Extremely Sensitive Magnetic Operate Point -- 4 Oersteds
Digital Output
Frequency Response to >100 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op./
Release
(Oe)
ON|OFF
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
4|-4
2
0.4
Current Sink
FCMe
Cross axis
MSOP8 (Pb)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
The IL721T-3 is a high temperature, 3.3/5V dual-channel, bi-directional isolated buffer. Channel configuration is the reverse of the IL712T. 110 Mbps, CMOS compatible with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin SOIC package.