New Products

Displaying 141 to 160 (of 407 products)
IL710-1E: 1-Channel Isolator, 1 kV, MSOP

The IL710-1 is a 3.3V/5V, single channel, 110 Mbps CMOS-compatible isolated buffer, with enable, 10 ns propagation delay, 3 ns pulse width distortion with 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package. This part is lead (Pb) free.

Part Number:
IL710-1E
Quantity in Stock:
25

$3.58

AAH002-02E PCBA: Ultrahigh Sensitivity Analog Sensor Assembly

A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.

Part Number:
AAH002-02E PCBA
Quantity in Stock:
27

$150.00

AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board

This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040C
Quantity in Stock:
27

$16.95

AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board

This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040B
Quantity in Stock:
31

$19.95

AG956-07E: ASR002-10E Smart SPI Angle Sensor Evaluation Kit

The AG956-07 Evaluation Kit has everything you need to calibrate, test, and evaluate the remarkable ASR002-10E Smart Angle Sensor. The kit includes:
    • An evaluation board with:
          - an ASR002-10E sensor
          - a diametrical magnet
          - magnet fixturing and a

    • An interface board with:
          - a microcontroller connected to the sensor via SPI
          - flexibility to power from USB or external power supply
          - isolated USB interface for safety and low noise.

    • A powerful, intuitive graphical user interface.

    • Simple software installation.

    • USB cable to connect the Evaluation Board to a computer.

Part Number:
AG956-07E
Quantity in Stock:
32

$195.00

AD020-00E: 2.8 mT Digital Switch, RoHS MSOP

NVE's AD020-00 GMR Switch integrates GMR sensor elements with digital onboard signal processing electronics. The GMR Switch has less field sensing errors than other magnetic sensors, and magnetic field operate points are stable over voltage and temperature extremes. This enables high precision, tight-tolerance magnetic sensing assemblies. Features: Precision Magnetic Operate Point --28 Oersteds Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 21-34 5 0.4 Current Sink BBK Std. axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AD020-00E
Quantity in Stock:
33

$4.89

IL712-1E: 2-Channel (1 each direction) Isolator, 1 kV, MSOP

The IL712-1 is a 3.3/5V, dual-channel bidirectional 110 Mbps CMOS-compatible isolated buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package. This part is lead (Pb) free.

Part Number:
IL712-1E
Quantity in Stock:
38

$5.83

IL721E: Widebody 2-Channel (1 each direction) Isolator, 2.5 kV, Wide SOIC

The IL721 is a high speed bidirectional isolator in NVE's unique True 8 mm creepage wide-body package. 110 Mbps, 100C, 10 ns propagation delay, 3 ns pulse width distortion. 16-pin True 8(TM) wide SOIC.

Part Number:
IL721E
Quantity in Stock:
39

$5.83

AD324-00E: 2.8 mT Digital Switch, RoHS MSOP

NVE's AD324-00E GMR Switch integrates GMR sensor elements with digital onboard signal processing electronics. The GMR Switch has less field sensing errors than other magnetic sensors, and magnetic field operate points are stable over voltage and temperature extremes. This enables high precision, tight-tolerance magnetic sensing assemblies. Features: Precision Magnetic Operate Point -- 28 Oersteds Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 21-34 5 0.4 Current Sink GBF Cross axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AD324-00E
Quantity in Stock:
40

$4.89

SM225-10E: High-Speed Smart TMR Magnetometer, 15mT, SPI, TDFN6

The SM225-10E Smart Magnetometer combines a Tunneling Magnetoresistance (TMR) sensor element with sophisticated digital signal processing for a unique combination of speed and precision. An SPI interface provides data as well as an external programming interface.

Unlike awkward, old-fashioned Hall-effect sensors, TMR is sensitive in-plane for optimal current sensing and easy mechanical interfaces. Key features include:
  •  0 to 150 Oe / 0 to 15 mT linear range
  •  Can detect magnets more than 50 mm away
  •  SPI interface
  •  2% of full-scale accuracy for 0 to 125°C
  •  Fast 15000 sample-per-second update rate
  •  Factory calibrated
  •  Programmable offset and gain compensation
  •  -40°C to +125°C operating range
  •  Ultraminiature 2.5 x 2.5 mm TDFN package

Part Number:
SM225-10E
Quantity in Stock:
40

$6.88

ALT021-10E-EVB01: 0-0.25 mT TMR magnetometor eval board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.

Part Number:
ALT021-10E-EVB01
Quantity in Stock:
41

$19.95

IL7611VE: Two-channel (both same direction) Isolator w/3.3-3.3V DC-DC Convertor

The IL7611VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7611VE
Quantity in Stock:
45

$11.16

AD105-00E: 4 mT Digital Switch, RoHS MSOP

NVE's AD105-00E GMR Switch integrates GMR sensor elements with digital onboard signal processing electronics. The GMR Switch has less field sensing errors than other magnetic sensors, and magnetic field operate points are stable over voltage and temperature extremes. This enables high precision, tight-tolerance magnetic sensing assemblies. Features: Precision Magnetic Operate Point -- 40 Oersteds Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 30-50 5 0.4 Current Source DBG Std. axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AD105-00E
Quantity in Stock:
48

$4.89

ALT021-10E-EVB02: 0-0.25 mT TMR eval board w/amplifier

A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.

The board can be powered by a 0.9 to 7 V power supply or battery and provides a linear, single-ended output.

Part Number:
ALT021-10E-EVB02
Quantity in Stock:
48

$49.95

ADK991-14E: 350 mT, 3V Nanopower TMR Switch, ULLGA

The ADK991-14E Nanopower Switch integrates TMR sensor elements with digital signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: 350 mT Digital Switch Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V 1 microamp quiescent current at 3 V without duty-cycling Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package Applications: MRI Detection Battery-Powered Devices Portable Instruments Wearables

Part Number:
ADK991-14E
Quantity in Stock:
50

$17.05

IL260-1-01: 5-Ch (all same dir) QSOP Isolator Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards have an IL260-1E ultraminiature five-channel (all the same direction) QSOP isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.

The board lets you evaluate the world's smallest high-performance isolators.

Part Number:
IL260-1-01
Quantity in Stock:
50

$49.95

IL261-1-01: 5-Ch (4-xmt, 1-rcv) QSOP Isolator Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards have an IL261-1E ultraminiature five-channel (four transmit, one receive) QSOP isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.

The board lets you evaluate the world's smallest high-performance isolators.

Part Number:
IL261-1-01
Quantity in Stock:
50

$49.95

IL3685T-01: 40Mbps, 125C Isolated Xcvr Eval Bd, Wide SOIC

These 2 x 3.5-inch (50 x 90 mm) boards include an IL3685TE isolated RS-485 transceiver, a termination resistors, power-supply bypass capacitors as recommended, screw connections, provisions for header pins, and a DB9 bus connector for PROFIBUS.

The IL3685TE is the world's fastest isolated transceiver with data rates to 40 Mbps, is fully PROFIBUS compatible, including the stringent bus differential specifications, and is rated to a full 125C.

Part Number:
IL3685T-01
Quantity in Stock:
50

$49.95

IL4822-01: Isolated RS-485 Xcvr w/5V bus DC-DC Conv Eval Bd

This Evaluation Board is a complete isolated RS-485 node using the IL4822E isolated transceiver with integrated DC-to-DC convertor.

These 2 x 3.5-inch (50 x 90 mm) boards include screw terminals and test pads. LEDs indicate DC-to-DC convertor input and output power. A 2s2p board with vias optimizes thermal performance.

The IL4822E is a high-speed, fully-isolated, full-duplex differential bus transceiver with an integrated DC-to-DC convertor to create an isolated 5 volt bus supply using the 3.3 volt controller supply. This level of integration dramatically reduces chip count and board area.

Part Number:
IL4822-01
Quantity in Stock:
50

$84.95

IL611-3-01: IL611-3E 2-Ch (both same dir) Passive-In Isolator Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards have an IL611-3E two-channel (both the same direction) SOIC8 passive isolator, input resistors and capacitors, a power-supply bypass capacitor as recommended, screw connections, and provisions for header pins.

Award-winning IL600-Series Isolators provide unique passive inputs for flexibility similar to LED-input optocouplers but with better performance and higher package density. The devices are manufactured with NVE’s patented IsoLoop spintronic Giant Magnetoresistive (GMR) technology for small size, high speed, and low power.

Part Number:
IL611-3-01
Quantity in Stock:
50

$49.95

Displaying 141 to 160 (of 407 products)