The IL7611VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$11.16
The unique AHK991-14E is a high-field, low voltage, low power, TMR magnetic switch, designed for MRI detection in implantable medical devices.
The sensors have a 350 mT (3500 Oe) typical operate point, which is high enough to detect MRI fields or strong, rare-earth magnets in close proximity. Such high fields disrupt most other magnetic sensors.
The sensors can withstand unlimited fields without
being damaged or turning off.
Unlike Hall effect or other sensors, the switch is sensitive to magnetic fields in any direction.
Key Specifications:
350 mT operate point
0.9 to 1.8 V
2 µA typical supply current
3000 Hz switching speed
-40 to 85°C
$17.05
NVE's AD105-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 40 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
30-50
5
0.4
Current Source
DBG
Std. axis
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
$4.89
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM324-10E 0 to 1.5 mT precision Smart TMR magnetometer sensor.
The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and has a sophisticated I2C interface.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA003-02E 2 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA004-00E 5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA004-02E 5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA005-02E 10 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA006-00E 5 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA006-02E 5 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAH002-02E ultrahigh-sensitivity 0.6 to 3 mT linear range GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAH004-00E 1.5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAL002-02E 1.5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAL024-10E 1.5 mT saturation, low hysteresis GMR analog bridge magnetometer. Its cross-axis sensitivity makes it ideal for noncontact current sensing, which can be evaluated using this board.
The board has a pre-soldered sensor, screw terminals for the current trace, a standard 0.1" (2.54 mm) header, and a 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field or current.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ACT001-10E TMR analog bridge current sensor. The sensor
has an on-chip current strap for precise operation.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 14 V supply and provides a differential output voltage proportional current.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AKT001-14E high-field (1.5 T), low power TMR analog bridge magnetometer. The sensor is an ultraminiature 1.1 x 1.1 mm package.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
$19.95
These 2 x 3.5-inch (50 x 90 mm) boards have an IL260-1E ultraminiature five-channel (all the same direction) QSOP isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The board lets you evaluate the world's smallest high-performance isolators.
$49.95
These 2 x 3.5-inch (50 x 90 mm) boards have an IL261-1E ultraminiature five-channel (four transmit, one receive) QSOP isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The board lets you evaluate the world's smallest high-performance isolators.
$49.95
The RS-485 QSOP Isolated Transceiver Evaluation Board provides a complete isolated RS-485 node using the world's isolated transceiver, the IL3085-1E. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
Isolating RS-485 nodes reduces noise, eliminates ground loops, and improves safety.
$74.95