A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
The IL511-1 is a 3.3V/5V, dual-channel unidirectional 2 Mbps DC-correct digital isolator, 25 ns propagation delay, 10 ns pulse width distortion with 1 kVrms isolation and 50 kV/microsecond typical transient immunity, -40°C to 85°C. Unique 8-pin MSOP.
The "E" suffix indicates this part is lead (Pb) free.
The AG951-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable SM324-10E Smart TMR Magnetometer. The kit includes:
An evaluation board with:
- an SM324-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A powerful, intuitive graphical user interface.
Simple software installation.
Flexibility to power from USB or an external power supply.
Isolated USB interface for safety and noise minimization.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The IL710-1 is a 3.3V/5V, single channel, 110 Mbps CMOS-compatible isolated buffer, with enable, 10 ns propagation delay, 3 ns pulse width distortion with 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package.
This part is lead (Pb) free.
A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR002-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use SPI interface.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR012-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface.