The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
The AG951-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable SM324-10E Smart TMR Magnetometer. The kit includes:
An evaluation board with:
- an SM324-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A powerful, intuitive graphical user interface.
Simple software installation.
Flexibility to power from USB or an external power supply.
Isolated USB interface for safety and noise minimization.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
The IL610A-1E is a 3.3/5V, single-channel, 10 Mbps isolated signal coupler with an open-drain output, which can be used to replace opto-couplers in many standard isolation functions. The device is manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged coupler).
This part is lead (Pb) free.
Lead-free
product information
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR002-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use SPI interface.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR012-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR022-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an encoder-compatible ABZ interface.
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
NVE's AD020-00 GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point --28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
BBK
Std. axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The AAK001-14E is a high-field magnetometer sensor that provides precise sensing
of magnetic fields up to 4 kOe (400 mT). With a unique 1.1 mm x 1.1 mm package
package, it is also our smallest analog sensor.
Features:
Precise sensing of magnetic fields up to 4 kOe (400 mT)
Sensitive to fields of any direction in the IC plane
Ratiometric Wheatstone bridge outputs
Any operating supply voltage up to 12V
Ultraminiature 1.1 x 1.1 mm package
Applications:
Brushless DC motors
Motor commutator sensors
Noncontact high-current measurement
Harsh industrial applications
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
NVE's AD324-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
GBF
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.