A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.
The board can be powered by a 0.9 to 7 V supply or battery and provides a linear, single-ended output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
NVE's AD020-00 GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point --28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
BBK
Std. axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
NVE's AD324-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
GBF
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT024-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT002-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM124-10E 0 to 1 mT Smart GMR magnetometer sensor.
The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface as well as a magnetic threshold output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM324-10E 0 to 1.5 mT precision Smart TMR magnetometer sensor.
The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and has a sophisticated I2C interface.
NVE's AD105-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 40 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
30-50
5
0.4
Current Source
DBG
Std. axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.