A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT026-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
The ALT026 is a Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor
with extraordinary signal amplitude and wide linear range. The differential bridge
output is bipolar, meaning it is positive for a positive field and negative for
an opposite field polarity. The ALT025 has cross-axis sensitivity (across the pads).
Features:
Large signal (200 mV/V)
Wheatstone bridge magnetometer configuration
0 - 10 V power supply
20 kiloohm device resistance for low power
±20 mT (±200 Oe) linear range
High linearity output (
NVE's DB001-00E signal processing IC is designed to work with NVE's AD9xx series GMR switch with short circuit protection. This combination provides a high-current switched output that corresponds to the sensor input. The DB001-00E functions as the front end of a complete sensor assembly, and includes protection against short circuits and high voltage transients from capacitive and inductive loads. The parts also feature thermal shutdown circuitry and reverse battery protection. They provide a regulated output voltage for the sensor and other components in the assembly, and an LED driver to indicate an "ON" condition.
Features:
High Current Output
Reverse Battery and Transient Protection
LED Driver
Excellent Temperature and Voltage Performance
Small, Low Profile Surface Mount Packages
Note: Parts must be purchased in multiples of 100 when purchased in quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The IL017E is a low-power, 3.3/5V, 10 Mbps, 100C Isolator. Typical total quiescent current is just 0.3 mA per channel. 3/1 channel configuration is ideal for isolating SPI. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
Up to 20 Mpbs, 3.3 V or 5.0 V input logic, 15 kV bus ESD protection, and 20 kV per microsecond transient immunity. 16-pin narrow-body (0.15'') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The IL3685 is an isolated 40 Mbps RS-485 transceiver for 3.3V buses. 1/5 unit load supports up to 160 nodes. 3.3 V or 5 V input logic. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
This part is lead (Pb) free.
The QSOP isolated CAN Evaluation Board provides a complete isolated Controller Area Network node using the world's smallest isolated CAN transceiver, the IL41050TA-1E.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
The IL41050TFDE is an isolated CAN FD transceiver. 125C; 5 Mbps; 3.3 V or 5.0 V input logic.
16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
This Evaluation Board is a complete isolated RS-485 / RS-422 node using the IL4622E isolated transceiver with integrated isolated DC-DC convertor.
These 2 x 3.5-inch (50 x 90 mm) boards include screw terminals and test pads. LEDs indicate DC-to-DC convertor input and output power. A 2s2p board with vias optimizes thermal performance.
The IL4622E is a high-speed, fully-isolated, full duplex differential bus transceiver with an integrated
3.3-to-3.3 volt DC-DC convertor to provide a fully-isolated 3.3 volt bus supply using the controller supply. This level of integration dramatically reduces chip count and board area.
The IL485W performs the same EIA-485 and PROFIBUS functions as the IL485, but has an additional uncommitted isolation channel which is useful for fault detection in bus contention situations.
The "E" suffix indicates this part is lead (Pb) free.
The IL510-1 is a 3.3V/5V, single-channel, 2 Mbps DC-correct digital isolator, with optional external synchronization clock, output enable, 25 ns propagation delay, 10 ns pulse width distortion with 1 kVrms isolation and 20 kV/microsecond transient immunity, -40°C to 85°C. Unique 8-pin MSOP.
The "E" suffix indicates this part is lead (Pb) free.
The IL516 is a 3.3V/5V, multichannel 2 Mbps DC-correct digital isolator, 25 ns propagation delay, 10 ns pulse width distortion with 2500 Vrms isolation and 20 kV/microsecond transient immunity, -40°C to 85°C. 16-pin narrow-body (0.15"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL610-1E is a 3.3/5V, single-channel, 100 Mbps isolated signal coupler with a CMOS output, which can be used to replace opto-couplers in many standard isolation functions. The device is manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged coupler).
This part is lead (Pb) free.
Lead-free
product information
This 2 x 3.5-inch (50 x 90 mm) board showcases the unique IL610A-1E passive-input, open-drain isolator. A pushbutton and LED demonstrate the remarkable flexibility of this devices. The evaluation board also has an input resistor, input capacitor, power-supply bypass capacitor as recommended, as well as screw connections, test points, and provisions for header pins.
Award-winning IL600-Series Isolators provide unique flexibility similar to LED-input optocouplers but with better performance and higher package density. The MSOP package is the world's smallest isolator.
The devices are manufactured with NVE’s patented IsoLoop spintronic Giant Magnetoresistive (GMR) technology for small size, high speed, and low power.
The IL611-1E is a 3.3/5V, dual-channel, 100 Mbps isolated signal coupler with CMOS outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged couplers).
This part is lead (Pb) free.
Lead-free
product information