The IL485W performs the same EIA-485 and PROFIBUS functions as the IL485, but has an additional uncommitted isolation channel which is useful for fault detection in bus contention situations.
Features include 3.3 V or 5.0 V input logic, 15 kV bus ESD protection, 5 Mbps data rate, and 20 kV per microsecond transient immunity. 16-pin wide-body (0.3'') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The IL721-3 is a 3.3/5V, dual-channel bidirectional isolated buffer. The channel configuration is reversed from the IL712. CMOS-compatible with automatic level shifting, 110 Mbps, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 8-pin SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The ALT025-14E is an ultraminiature Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor
with an extraordinary amount of signal. The differential bridge
output is bipolar, meaning it is positive for a positive field and negative for
an opposite field polarity.
Features:
Tunneling Magnetoresistive Technology (TMR)
Large signals (20 mV/V/mT typical)
Wheatstone bridge magnetometer configuration
20 kiloohm device resistance for low power
±10 mT linear range
1.1 x 1.1 mm DFN4 package
–40 to 125°C
Applications:
Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
NVE's ABL016-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.3 mm apart on the sensor IC, and the two sensors are phase shifted by 0.15 mm.
Bridge Resistance for Each Bridge (Ohms)
Linear Range (Oersteds)
Output
Comments
Package
Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.300 mm, and phase shift from sensor to sensor is 0.150 mm.
4K - 7K
+/-5 to +/-100
Dual Analog Bridge
Gear Tooth or Encoder
TDFN6
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The IL712V-1 is a dual-channel bidirectional 110 Mbaud CMOS-compatible isolated buffer with full 2.5 kVrms isolation voltage in a unique 8-pin MSOP package. 10 ns propagation delay, 3 ns pulse width distortion, and 50 kV/microsecond transient immunity.
The "E" suffix indicates this part is lead (Pb) free.
AB001-02E GMR Gradient Sensors (Gradiometers) offer unparalleled magnetic gradient
sensing. Two pairs of unshielded GMR bridge resistors provide directional sensing
of small gradients over a wide range of magnetic field strength. The devices
are sensitive only to gradients, and have low sensitivity to constant magnetic
noise.
Differential magnetic field sensor (gradiometer) --
for gear tooth, multi-pole magnet, and high noise rejection sensing.
Typ. Min. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
250
20 - 200
0.02 - 0.03
2,500 +/-20%
SOIC8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 92) when purchasing quantities of 92 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
NVE's ADL922-14E Ultraminiature Nanopower Switch integrates GMR sensor elements with onboard digital signal processing. Continuous operation allows high frequency switching. External duty cycling allows nanopower operation. The part is packaged in a 1.1 x 1.1 x 0.35 mm DFN4 package.
Features:
Precise 4 mT operate point
Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm DFN4 package
2.4 to 4.2 V
Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling
100 kHz Operating Frequency
Digital Switch Output
Applications:
Battery-Powered Devices
Wearables and IoT Sensors
Battery-Powered Devices
Industrial Sensors
NVE's AFL000-00E low power switch sensor integrates GMR sensor elements with digital
onboard signal processing electronics. The switch is designed for use in low power
and battery applications, and features supply voltages down to 0.9 Volts and
continuous operation at currents of 20-55 microamps. Like all NVE magnetic sensors,
the AFL sensors have extremely precise magnetic operate and release points.
Features:
Precision Magnetic Operate Point -- 10 Oersteds
Low Voltage -- 0.9 V
Low Power
Digital Output
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Single Battery Applications
Low Power, Low Field Applications
Supply
Voltage
min.-max.
Supply
Current
(µA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
0.9-1.3
20-55
7-13
1
0.4
Current Sink
PBBe
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
The 12030 is a 0.125 x 0.25 x 0.5 inch miniature ferrite bar magnet. Typical
field strength is 1500 Oe at the magnet face and forty oersteds one-half inch
away.
This magnet is also included in several sensor evaluation kits, including our Analog
Sensor Evaluation Kit and Sensor
Demo Board.
NVE's AD122-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 40 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
30-50
5
0.4
Current Source
DBC
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The IL613E is a 3.3/5V, 3-channel (all in same direction), 100 Mbps isolated signal coupler with CMOS outputs which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 16-pin 0.3" SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The IL611A-3E is a 3.3/5V, dual-channel, 10 Mbps isolated signal coupler with open-drain outputs which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged couplers).
This part is lead (Pb) free.
Lead-free
product information
The DC001-10E 5V regulator is designed for harsh, noisy environments where immunity to large voltage transients and high input voltages are required. These regulators protect the sensitive electronic components while providing a stable regulated supply. They are rated for high temperature operation, up to 175 degrees Celsius. The low profile, small footprint package features an exposed die-attach pad for direct heat sinking to the circuit board.
Features:
Input voltage to 36VDC
5V Regulated Output
Reverse Battery Protection
Excellent immunity to Transients and ESD
Small, Low Profile Surface Mount Packages
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is lead (Pb) free.
Lead-free
product information
The IL260-1E is an ultraminiature isolator with no performance compromises. 110 Mbps, 10 ns propagation delay, 3 ns pulse width distortion, 600 WV per VDE 0884-10, 2500 Vrms isolation and 50 kV/microsecond transient immunity, and 44000 year barrier life. 16-pin QSOP.
The "E" suffix indicates this part is lead (Pb) free.
The IL611-2E is a 3.3/5V, dual-channel, 100 Mbps isolated signal coupler with CMOS outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin PDIP package.
This part is lead (Pb) free.
Lead-free
product information