New Products
IL3085TE: 4 Mbps Isolated RS485 Transceiver, 125C, 2.5kV, Wide SOIC
The IL3085TE is an isolated 4 Mbps RS-485 transceiver with an extended temperature range. Compatible with 3.3 V or 5 V input logic. 16-pin wide-body SOIC package with True 8™ mm creepage.
- Part Number:
- IL3085TE
- Quantity in Stock:
- 85
$5.56
12032: 1.0" x 0.125" x 0.39" Bar Magnet
The 12032 is a 1.0" long x 0.125" wide x 0.39" thick Y25 ferrite bar magnet. Typical field strength is 1800 Oe at the magnet face. This magnet is also included in the AG910-07 and AG911-07 GMR Switch Evaluation Kits.
- Part Number:
- 12032
- Quantity in Stock:
- 86
$4.25
IL422: Isolated RS422 Transceiver, 2.5 kV, Wide SOIC (Pb)
Galvanically-isolated full-duplex RS-422 interface in a 0.3" 16-pin SOIC package. 2500 Vrms isolation and 20 kV/microsecond transient immunity.
- Part Number:
- IL422
- Quantity in Stock:
- 94
$14.57
IL7615VE: 4-channel (all same direction) Isolator w/3.3-3.3V DC-DC Convertor
The IL7615VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
- Part Number:
- IL7615VE
- Quantity in Stock:
- 96
$12.40
IL4685-01: Isolated RS-485 Xcvr w/3 V bus DC-DC Conv Eval Bd
This Evaluation Board is a complete isolated RS-485 node using the IL4685E isolated transceiver with integrated isolated DC-DC convertor.
These 2 x 3.5-inch (50 x 90 mm) boards include screw terminals and test pads. LEDs indicate DC-to-DC convertor input and output power. A 2s2p board with vias optimizes thermal performance.
The IL4685E is a high-speed, fully-isolated, half-duplex differential bus transceiver with an integrated DC-to-DC convertor to create an isolated 3.3 volt bus supply using the 3.3 volt controller supply. This level of integration dramatically reduces chip count and board area.
- Part Number:
- IL4685-01
- Quantity in Stock:
- 100
$84.95
IL612A-3E: 2-Channel Passive Input, Open-Drain Isolator, 2.5 kV, SOIC8
The IL612A-3E is a 3.3/5V, dual-channel, 10 Mbps isolated signal coupler with open-drain outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin SOIC package. This part is lead (Pb) free. Lead-free product information
- Part Number:
- IL612A-3E
- Quantity in Stock:
- 171
$5.43
SM228-10E: Smart TMR Magnetometer, 15 mT, I2C, TDFN6
The SM228-10E Smart Magnetometer combines a Tunneling Magnetoresistance (TMR) sensor element with
sophisticated digital signal processing for a unique combination of speed and precision. An I2C interface provides data as well as an external programming interface.
Unlike awkward, old-fashioned Hall-effect sensors, TMR is sensitive in-plane for
optimal current sensing and easy mechanical interfaces. Key features include:
• 0 to 150 Oe / 0 to 15 mT linear range
• Can detect magnets more than 50 mm away
• I2C interface
• Programmable digital threshold output
• 2% of full-scale accuracy for 0 to 125°C
• Fast 10000 sample-per-second update rate
• Factory calibrated
• Programmable offset and gain compensation
• -40°C to +125°C operating range
• Ultraminiature 2.5 x 2.5 mm DFN6 package
- Part Number:
- SM228-10E
- Quantity in Stock:
- 175
$6.88
IL711T-1E: 125C 2-Channel (both same direction) Isolator, 1 kV, MSOP
The IL711T-1 is a high temperature, 3.3/5V, dual-channel, unidirectional, 110 Mbps, CMOS compatible isolated buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package. The "E" suffix indicates this part is lead (Pb) free.
- Part Number:
- IL711T-1E
- Quantity in Stock:
- 207
$6.29
IL7617VE: 4-channel (3 transmit, 1 receive) Isolator w/3.3-3.3V DC-DC Convertor
The IL7617VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
- Part Number:
- IL7617VE
- Quantity in Stock:
- 224
$12.40
AG904-06: ULLGA General-Purpose PCB
A 1.2 x 0.25 inch x 0.031 inch thick (30 x 6 x 0.75 mm) PCB for demonstrating 1.1 x 1.1 mm ULLGA4 sensors (-14E sensor suffix; order sensors separately).
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
- Part Number:
- AG904-06
- Quantity in Stock:
- 237
$5.00
AD021-00E: 2 mT Digital Switch, RoHS MSOP
NVE's AD021-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 20 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
15-25
5
0.4
Current Sink
BBB
Cross axis
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
- Part Number:
- AD021-00E
- Quantity in Stock:
- 239
$4.89
ALT023-10E: 0-1 mT TMR Bipolar Analog Sensor, 20 KOhm, x-axis, TDFN6
The ALT023 is a Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor with extraordinary sensitivity. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. Features: ±1 mT linear range Large signal (200 mV/V/mT typical) Wheatstone bridge magnetometer configuration 0 - 10 V power supply 20 kiloohm device resistance for low power High linearity output (
- Part Number:
- ALT023-10E
- Quantity in Stock:
- 298
$12.00
IL610CMTI-1E: 1-Channel Ultrahigh CMTI Isolator, 2.5 kV, MSOP
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL610CMTI-1E is a single-channel version in an ultraminiature MSOP8 package.
- Part Number:
- IL610CMTI-1E
- Quantity in Stock:
- 303
$3.85
AD924-00E: 2.8 mT Digital Switch, RoHS MSOP
AD924-00E Sensors are for use with external high-current output transistors in
industrial control environments. The parts provide the same precise magnetic performance
as NVE's GMR Digital Switches with the addition of output stage short circuit
protection (SCP). The protection circuit shuts off the output stage if there is
a short circuit, then turns it back on after a specified interval. The sensor,
combined with external reverse battery and overvoltage protection, results in
a "bulletproof" assembly.
Features:
Precision Magnetic Operate Point -- 28 Gauss
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Sink/
Source/
Vreg/
SCP
NBF
Cross axis
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- AD924-00E
- Quantity in Stock:
- 327
$5.63
IL816TE: 4-Channel (2 each direction) Top-of-the-Line Isolator, 2.5 kV, Wide SOIC
The IL816TE is NVE's top-of-the-line four-channel isolator (2 each direction), with best-in-class specifications:
• 125°C max. operating temperature
• 110 Mbps
• 10 ns propagation delay
• DC-correct; deterministic power-up
• 50 kV/µs typ.; 30 kV/µs min. transient immunity
• IEC 60747-5-5 (VDE 0884) certified—600 Vrms WV
• 44000-year barrier life
• Low EMC footprint
The part uses NVE's unique True 8 eight-millimeter creepage 16-pin wide-body SOIC package.
- Part Number:
- IL816TE
- Quantity in Stock:
- 361
$8.40
IL614-3E: 3-Channel Passive Input, CMOS-Output Isolator, 2.5 kV, Narrow SOIC
The IL614-3E is a 3.3/5V, 3-channel (2 transmit, 1 receive), 100 Mbps isolated signal coupler with CMOS outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 16-pin 0.15" SOIC package. This part is lead (Pb) free. Lead-free product information
- Part Number:
- IL614-3E
- Quantity in Stock:
- 378
$6.99
IL41050TTE: Basic Isolated CAN Transceiver, 2.5 kV, Wide SOIC
The IL41050TT is a low-cost, basic CAN transceiver without Vref output and silent mode input pins. 2.5kV isolation; 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic. 16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
- Part Number:
- IL41050TTE
- Quantity in Stock:
- 410
$3.62
ABL014-00E: 1 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL014-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 1.0 mm apart on the sensor IC, and the two sensors are phase shifted by 0.5 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm, and sensor-to-sensor phase shift is 0.500 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL014-00E
- Quantity in Stock:
- 425
$6.29
AFL006-10E: 0.4 mT Digital Sw, 0.9 V – 2 V, Norm OFF Sinking, TDFN
The AFL006-10E is the world's most sensitive magnetic switch. The switch is designed for use in low power and battery applications. It can operate from a single cell with supplies as low as 0.9 V and typical supply current of 55 microamps. Like all NVE magnetic sensors, the AFL006-10E has extremely precise magnetic operate and release points. Features: 4 Oe typical operate point for ultrahigh sensitivity 0.9 V – 2 V operating voltage for single-cell battery operation Less than 100 microwatts power consumption 2.5 mm x 2.5 mm x 0.8 mm TDFN6 for miniaturization Applications include: Portable instruments Utility meters Noncontact overcurrent protection Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times. This part is RoHS compliant.
- Part Number:
- AFL006-10E
- Quantity in Stock:
- 434
$9.25
AG039-06: ULLGA Digital Sensor Demonstration Bare Board
A 1.57 x 0.25 inch PCB for demonstrating ADLxxx-14E/AHLxxx-14E 1.1 x 1.1 mm ULLGA4 digital sensors (order sensors separately). In addition to space for the sensor, the boards have locations for 0402-size pull-up resistors and bypass capacitors.
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
- Part Number:
- AG039-06
- Quantity in Stock:
- 466
$5.00
