NVE's AD724-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Regulated Voltage Output
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Sink/
Sink/
Vreg
LBF
Cross axis
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
$4.89
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL611CMTI-1E is a two-channel version in an ultramniature MSOP8 package.
$6.24
NVE's AD320-00E GMR Switch integrates GMR sensor elements with digital onboard
signal processing electronics. The GMR Switch has less field sensing errors than
other magnetic sensors, and magnetic field operate points are stable over voltage
and temperature extremes. This enables high precision, tight-tolerance magnetic
sensing assemblies.
Features:
Precision Magnetic Operate Point -- 28 Oersteds
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Current Sink
GBK
Std. axis
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
$4.89
ASR002 TMR Smart Angle Sensors provide a precise digital indication of magnetic rotation operating over a wide range of speeds.
The sensor combines a precise, low-power Tunneling Magnetoresistance (TMR) sensor with sophisticated digital signal processing.
The ASR002-10E provides an extraordinary combination of speed and precision, with a 12.5 kSps sample rate and ±0.2° repeatability.
The sensor is factory calibrated, with coefficients stored in
internal memory.
A four-wire SPI interface provides angle data and allows
setting device parameters.
The ASR002 is designed for harsh industrial or automotive environments with ESD protection and full −40°C to +125°C operating temperature range.
$8.98
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT026-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
$19.95
The IL7616VE is a four-channel (two each direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$12.40
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
$19.95
The IL016E is a low-power, 3.3/5V, 10 Mbps, 100C Isolator. Typical total quiescent current is just 0.3 mA per channel. 16-pin wide-body (0.3"-wide) SOIC package. The "E" suffix indicates this part is lead (Pb) free.
$8.23
The IL3085TE is an isolated 4 Mbps RS-485 transceiver with an extended temperature range. Compatible with 3.3 V or 5 V input logic. 16-pin wide-body SOIC package with True 8™ mm creepage.
$5.56
The 12032 is a 1.0" long x 0.125" wide x 0.39" thick Y25 ferrite bar magnet. Typical field strength is 1800 Oe at the magnet face. This magnet is also included in the AG910-07 and AG911-07 GMR Switch Evaluation Kits.
$4.25
Galvanically-isolated full-duplex RS-422 interface in a 0.3" 16-pin SOIC package. 2500 Vrms isolation and 20 kV/microsecond transient immunity.
$14.57
The IL7615VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$12.40
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA002-02E 0.15 to 1.05 mT GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
$19.95
The ALT023-10E is a Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor with extraordinary sensitivity. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. Features: ±1 mT linear range Large signal (200 mV/V typical) Extraordinary sensitivity (200 mV/V/mT typical) Wheatstone bridge magnetometer configuration 0 - 10 V power supply 20 kiloohm device resistance for low power High linearity output (
$12.00
The SM228-10E Smart Magnetometer combines a Tunneling Magnetoresistance (TMR) sensor element with
sophisticated digital signal processing for a unique combination of speed and precision. An I2C interface provides data as well as an external programming interface.
Unlike awkward, old-fashioned Hall-effect sensors, TMR is sensitive in-plane for
optimal current sensing and easy mechanical interfaces. Key features include:
0 to 150 Oe / 0 to 15 mT linear range
Can detect magnets more than 50 mm away
I2C interface
Programmable digital threshold output
2% of full-scale accuracy for 0 to 125°C
Fast 10000 sample-per-second update rate
Factory calibrated
Programmable offset and gain compensation
-40°C to +125°C operating range
Ultraminiature 2.5 x 2.5 mm DFN6 package
$6.88
The IL612A-3E is a 3.3/5V, dual-channel, 10 Mbps isolated signal coupler with open-drain outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin SOIC package. This part is lead (Pb) free. Lead-free product information
$5.43
A smart business card that demonstrates the ADT925-14E 1.1 x 1.1 mm DFN4 TMR Switch sensor.
The board can be plugged into a USB TYPE-A connector, such as those on a computer, for power. An LED on the card shows when the sensor is activated. A small neodymium magnet is included to activate the sensor.
You can carry it with you so you're always prepared to demonstrate the high sensitivity, low power, and small size of TMR sensors.
$19.95
NVE-branded 2 GB rotate-cover USB flash drive. NVE is named for nonvolatile electronics.
$8.95
The IL7617VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
$12.40
The ALT026 is a Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor with extraordinary signal amplitude and wide linear range. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. The ALT025 has cross-axis sensitivity (across the pads). Features: Large signal (200 mV/V) Wheatstone bridge magnetometer configuration 0 - 10 V power supply 20 kiloohm device resistance for low power ±20 mT (±200 Oe) linear range High linearity output (
$12.00