New Products

Displaying 1 to 20 (of 414 products)
12591: 2 mm pitch magnetic linear scale tape, 1 x 20 cm

This magnetic scale tape is designed to be used with AET200-00E 2 mm pitch linear sensor. 1 cm (0.4 inches) wide by 20 cm (8 inches) long.

Part Number:
12591

$30.00

AA007-00E: 50 mT Sat. Analog Sensor, 5 KOhm, RoHS MSOP

The AA007-00E GMR Magnetic Field Sensors are used to sense relatively high fields. 0.1 mV/V/Oe Sensitivity; 500 Oe Saturation Field; MSOP8.
Note: Parts must be purchased in tube quantities (multiples of 100) when purchasing quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AA007-00E

$9.60

ABL015-10E: 0.5 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS TDFN

NVE's ABL015-10E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.5 mm apart on the sensor IC, and the two sensors are phase shifted by 0.25 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm, and phase shift from sensor to sensor is 0.250 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL015-10E

$6.29

ABT250-00E: TMR 1 mm Pitch Gear Tooth Sensor, MSOP

ABT250-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.

The ABT250-00E is optimized for 1 mm pitch gears, and can be used for pitches from 0.6 to 2 mm. The sensors have two channels to detect direction.

Key features include:
   • 0.001° resolution
   • Large analog peak-to-peak signals
   • Operating frequency to 350 kHz
   • 150 °C operating temperature

Part Number:
ABT250-00E

$5.71

ABT375-00E: TMR 1.5 mm Pitch Gear Tooth Sensor, MSOP

ABT375-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.

The ABT375-00E is optimized for 1.5 mm pitch gears, and can be used for pitches from 1 to 3 mm. The sensors have two channels to detect direction.

Key features include:
   • 0.001° resolution
   • Large analog peak-to-peak signals
   • Operating frequency to 350 kHz
   • 150 °C operating temperature

A demo board is also available.

Part Number:
ABT375-00E

$5.71

ABT500-00E: TMR 2 mm Pitch Gear Tooth Sensor, MSOP

ABT500-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.

The ABT500-00E is optimized for 2 mm pitch gears, and can be used for pitches from 1.3 to 4 mm. The sensors have two channels to detect direction.

Key features include:
   • 0.001° resolution
   • Large analog peak-to-peak signals
   • Operating frequency to 350 kHz
   • 150 °C operating temperature

Part Number:
ABT500-00E

$5.71

ABT600-00E: TMR 2.4 mm Pitch Gear Tooth Sensor, MSOP

ABT600-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.

The ABT600-00E is optimized for 2.4 mm pitch gears, and can be used for pitches from 1.6 to 4.8 mm. The sensors have two channels to detect direction.

Key features include:
   • 0.001° resolution
   • Large analog peak-to-peak signals
   • Operating frequency to 350 kHz
   • 150 °C operating temperature

Part Number:
ABT600-00E

$5.71

AD024-00E: 2.8 mT Digital Switch, RoHS MSOP

NVE's AD024-00E GMR Switch integrates GMR sensor elements with digital onboard signal processing electronics. The GMR Switch has less field sensing errors than other magnetic sensors, and magnetic field operate points are stable over voltage and temperature extremes. This enables high precision, tight-tolerance magnetic sensing assemblies. Features: Precision Magnetic Operate Point -- 28 Oersteds Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 21-34 5 0.4 Current Sink BBF Cross axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times. This part is RoHS compliant.

Part Number:
AD024-00E

$4.89

AD084-00E: 2.8 mT Digital Switch, RoHS MSOP

NVE's AD084-00E GMR Switch integrates GMR sensor elements with digital onboard signal processing electronics. The GMR Switch has less field sensing errors than other magnetic sensors, and magnetic field operate points are stable over voltage and temperature extremes. This enables high precision, tight-tolerance magnetic sensing assemblies. Features: Precision Magnetic Operate Point -- 28 Oersteds Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 3.0-6.0 0.7-1.2 21-34 5 0.4 Current Sink BDF Cross axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times. This part is RoHS compliant.

Part Number:
AD084-00E

$4.89

AD924-00: 2.8 mT Digital Switch, MSOP

AD924-00 Sensors are for use with external high-current output transistors in industrial control environments. The parts provide the same precise magnetic performance as NVE's GMR Digital Switches with the addition of output stage short circuit protection (SCP). The protection circuit shuts off the output stage if there is a short circuit, then turns it back on after a specified interval. The sensor, combined with external reverse battery and overvoltage protection, results in a "bulletproof" assembly. Features: Precision Magnetic Operate Point -- 28 Gauss Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 21-34 5 0.4 Sink/
Source/
Vreg/
SCP NBF Cross axis MSOP8
(Pb) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AD924-00

$5.65

ADL121-14E: 2 mT, 3V, 30 Hz Duty-Cycled GMR Switch, ULLGA

NVE's ADL121-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V Typical Power Consumption 72 nW at 2.4 V 30 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycling Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL121-14E

$5.63

ADT005-10E: High Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6

ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.

The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.

To minimize power, the ADT005 does not include the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.

The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.

The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.

Part Number:
ADT005-10E

$11.18

ADT924-14E: 2.2 mT, 3V Nanopower TMR Switch, ULLGA

NVE's ADT924-14E Nanopower Switch integrates TMR sensor elements with digital signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: 2.2 mT (22 Oe) Digital Switch Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V 1 microamp quiescent current at 3 V without duty-cycling Up to 20 kHz switching frequency Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package Applications: Battery-Powered Devices Portable Instruments Wearables

Part Number:
ADT924-14E

$11.18

AET050F-00E: 0.5 mm, Full-Bridge TMR Rotational / Linear Sensor, MSOP

AET050F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.

The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.

Evaluation and Demonstration Kits are also available.

Part Number:
AET050F-00E

$5.71

AET075F-00E: 0.75 mm, Full-Bridge TMR Rotational / Linear Sensor, MSOP

AET075F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.

The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.

Evaluation and Demonstration Kits are also available.

Part Number:
AET075F-00E

$5.71

AET120F-00E: 1.2 mm, Full-Bridge TMR Rotational / Linear Sensor, MSOP

AET120F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.

The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.

Evaluation and Demonstration Kits are also available.

Part Number:
AET120F-00E

$5.71

AFL006-10E: 0.4 mT Digital Sw, 0.9 V – 2 V, Norm OFF Sinking, TDFN

The AFL006-10E is the world's most sensitive magnetic switch. The switch is designed for use in low power and battery applications. It can operate from a single cell with supplies as low as 0.9 V and typical supply current of 55 microamps. Like all NVE magnetic sensors, the AFL006-10E has extremely precise magnetic operate and release points. Features: 4 Oe typical operate point for ultrahigh sensitivity 0.9 V – 2 V operating voltage for single-cell battery operation Less than 100 microwatts power consumption 2.5 mm x 2.5 mm x 0.8 mm TDFN6 for miniaturization Applications include: Portable instruments Utility meters Noncontact overcurrent protection Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times. This part is RoHS compliant.

Part Number:
AFL006-10E

$9.25

AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board

The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040T

$19.95

AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit

The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.

The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.

Part Number:
AG903B-07E

$75.00

AG905-07E: ALT025 High Current PCB Demonstration

This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.

Part Number:
AG905-07E

$75.00

Displaying 1 to 20 (of 414 products)