New Products

Displaying 21 to 40 (of 376 products)
AG921-07E: AKL001 Gear-Tooth Sensor Demonstrator

A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".

Part Number:
AG921-07E
Quantity in Stock:
2

$90.00

AG932-07E: ADT002 Rotation Sensor Evaluation Kit

The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.

Part Number:
AG932-07E
Quantity in Stock:
11

$90.00

AG941-07E: ADL-Series Sensor Demo Board

The kit includes a demo board with three ultraminiature, ultralow-power ADL-Series magnetic sensors. Each sensor drives an indicator LED, and a meter shows the sensor power in microamps or nanoamps. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by a coin cell (included).

Part Number:
AG941-07E
Quantity in Stock:
4

$90.00

IL2985-ILDC11-01: Isolated 5V RS-485 Xcvr/DC-DC Conv Eval Bd

This board implements a complete isolated 5-volt RS-485 node using an IL2985E low-power transceiver, an ILDC11-15E ultraminiature isolated DC-DC convertor, and a commodity boost regulator.

The 4 by 3 inch (100 by 75 mm) board provides screw terminal and test point connections.

The IL2985E is a low-power, fully-isolated, differential 5-volt bus transceiver. The ILDC11-15E isolates the 3.3-volt controller supply, and a boost regulator provides a fully-isolated five-volt bus supply.

Part Number:
IL2985-ILDC11-01

$84.95

IL3685P-ILDC11-01: Isolated RS-485 Xcvr/DC-DC Conv Eval Bd

This Evaluation Board provides a complete isolated 3.3-volt RS-485 node using an IL3685PE isolated transceiver and an ILDC11-15E ultraminiature isolated DC-DC convertor. The 4 by 3 inch (100 by 75 mm) board provides screw terminal and test point connections.

The IL3685PE is a high-speed, fully-isolated, differential 3.3-volt bus transceiver.

The ILDC11-15E 3.3-to-3.3 volt DC-DC convertor provides a fully-isolated 3.3-volt bus supply using the controller supply.

Part Number:
IL3685P-ILDC11-01
Quantity in Stock:
8

$84.95

IL4622-01: Isolated RS-485/RS-422 Xcvr w/Integ DC-DC Conv Eval Bd

This Evaluation Board is a complete isolated RS-485 / RS-422 node using the IL4622E isolated transceiver with integrated isolated DC-DC convertor.

The 4 by 3 inch (100 x 75 mm) board provides screw terminal and test point connections, and uses a 2s2p board with thermal vias for optimal thermal performance.

The IL4622E is a high-speed, fully-isolated, full duplex differential bus transceiver with an integrated 3.3-to-3.3 volt DC-DC convertor to provide a fully-isolated 3.3 volt bus supply using the controller supply. This level of integration dramatically reduces chip count and board area.

Part Number:
IL4622-01
Quantity in Stock:
3

$84.95

AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit

The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.

The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.

Part Number:
AG903B-07E
Quantity in Stock:
5

$75.00

AG905-07E: ALT025 High Current PCB Demonstration

This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.

Part Number:
AG905-07E
Quantity in Stock:
3

$75.00

AG930-07E: AAT001 1.25 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.

Part Number:
AG930-07E
Quantity in Stock:
7

$75.00

AG931-07E: AAT003 40 KOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.

Part Number:
AG931-07E
Quantity in Stock:
9

$75.00

AG933-07E: AAT009 6 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.

Part Number:
AG933-07E
Quantity in Stock:
4

$75.00

AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.

Part Number:
AG934-07E
Quantity in Stock:
5

$75.00

IL3085-1-01: RS-485 QSOP Isolator Evaluation Board

The RS-485 QSOP Isolated Transceiver Evaluation Board provides a complete isolated RS-485 node using the world's isolated transceiver, the IL3085-1E. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.

Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.

The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.

Isolating RS-485 nodes reduces noise, eliminates ground loops, and improves safety.

Part Number:
IL3085-1-01
Quantity in Stock:
3

$74.95

IL3585-01: RS-485 Wide-Body Isolator Evaluation Board

The RS-485 Wide-Body Isolator Evaluation Board provides a complete isolated RS-485 node using the popular 0.3" (8 mm) creepage IL3585E isolated transceiver. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.

Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.

The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.

Isolating RS-485 nodes reduces noise, eliminates ground loops, and improves safety.

Part Number:
IL3585-01
Quantity in Stock:
6

$74.95

IL3585-3-01: RS-485 Narrow-Body Isolator Evaluation Board

The RS-485 Narrow-Body Isolated Transceiver Evaluation Board provides a complete isolated RS-485 node using the unique 0.15"-wide IL3585-3E isolated transceiver. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.

Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.

The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.

Isolating RS-485 nodes reduces noise, eliminates ground loops, and improves safety.

Part Number:
IL3585-3-01
Quantity in Stock:
10

$74.95

IL3685-3-01: PROFIBUS Isolator Evaluation Board

The PROFIBUS Isolated Transceiver Evaluation Board provides a complete isolated PROFIBUS node using the unique 0.15" narrow-body IL3685-3E isolated transceiver. The board provides screw terminal and PROFIBUS DB9 connections.

Termination, pull-up, and pull-down resistors are typical PROFIBUS values, and easily changed for specific applications.

The transceiver provides data rates to 40 Mbps, and is fully PROFIBUS compatible, including the stringent bus differential specifications.

Part Number:
IL3685-3-01
Quantity in Stock:
10

$74.95

12545: Holder for 8 mm dia. disk magnet

A machined-aluminum magnet holder for 8 mm dia. magnets such as part numbers 12527 and 12528 (sold separately).

Compatible with AG93x-Series and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.

Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.

Part Number:
12545
Quantity in Stock:
3

$70.00

12546: Holder for 4 mm dia. disk magnet

A machined-aluminum magnet holder for 4 mm dia. magnets such as part number 12526 (sold separately).

Compatible with AG93x-Series and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.

Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.

Part Number:
12546
Quantity in Stock:
3

$70.00

AG911-07E: GMR Switch Evaluation Kit

AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.

Part Number:
AG911-07E
Quantity in Stock:
11

$65.00

AG920-07E: GT Sensor Evaluation Kit

The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.

Part Number:
AG920-07E
Quantity in Stock:
13

$65.00

Displaying 21 to 40 (of 376 products)