New Products

Displaying 81 to 100 (of 385 products)
IL41050TFD-1E: Isolated CAN FD Transceiver, 125C, 5 Mbps, 2.5 kV, QSOP

The IL41050TFD-1E is an ultraminiature isolated CAN FD transceiver with no performance compromises. 125C; 5 Mbps; 3.3 V or 5.0 V input logic. 16-pin QSOP package--the world's smallest isolated transceiver.

Part Number:
IL41050TFD-1E
Quantity in Stock:
2465

$4.52

AD724-00E: 2.8 mT Digital Switch, RoHS MSOP

NVE's AD724-00E GMR Switch integrates GMR sensor elements with digital onboard signal processing electronics. The GMR Switch has less field sensing errors than other magnetic sensors, and magnetic field operate points are stable over voltage and temperature extremes. This enables high precision, tight-tolerance magnetic sensing assemblies. Features: Regulated Voltage Output Precision Magnetic Operate Point -- 28 Oersteds Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 21-34 5 0.4 Sink/
Sink/
Vreg LBF Cross axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AD724-00E
Quantity in Stock:
2880

$4.89

AG039-06: ULLGA Digital Sensor Demonstration Bare Board

A 1.57 x 0.25 inch PCB for demonstrating ADLxxx-14E/AHLxxx-14E 1.1 x 1.1 mm ULLGA4 digital sensors (order sensors separately). In addition to space for the sensor, the boards have locations for 0402-size pull-up resistors and bypass capacitors.

Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.

Part Number:
AG039-06
Quantity in Stock:
466

$5.00

AG904-06: ULLGA General-Purpose PCB

A 1.2 x 0.25 inch x 0.031 inch thick (30 x 6 x 0.75 mm) PCB for demonstrating 1.1 x 1.1 mm ULLGA4 sensors (-14E sensor suffix; order sensors separately).

Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.

Part Number:
AG904-06
Quantity in Stock:
486

$5.00

IL3022E: Low-Cost Isolated RS422 Transceiver, 2.5 kV, Wide SOIC

The IL3022E is a cost-effective isolated 4 Mbps RS-422 full-duplex transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL3022E
Quantity in Stock:
146

$5.05

IL3085E: Low-Cost Isolated RS485 Transceiver, 2.5 kV, Wide SOIC

The IL3085E is a cost-effective isolated 4 Mbps RS-485 transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL3085E

$5.05

ABL004-00E: 1 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS MSOP

NVE's ABL004-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 1.0 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL004-00E
Quantity in Stock:
5850

$5.15

ABL005-00E: 0.5 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS MSOP

NVE's ABL005-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.5 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL005-00E
Quantity in Stock:
9722

$5.15

ABL006-00E: 0.3 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS MSOP

NVE's ABL006-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.3 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.300 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL006-00E
Quantity in Stock:
1073

$5.15

ADL021-14E: 2 mT, 3V, 55 Hz Duty-Cycled GMR Switch, ULLGA

NVE's ADL021-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V Typical Power Consumption 192 nW at 2.4 V 55 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycling Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL021-14E

$5.15

ADL024-14E: 2.8 mT, 3V, 55 Hz Duty-Cycled GMR Switch, ULLGA

NVE's ADL024-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V Typical Power Consumption 192 nW at 2.4 V 110 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycling Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL024-14E
Quantity in Stock:
13210

$5.15

ADL121-14E: 2 mT, 3V, 30 Hz Duty-Cycled GMR Switch, ULLGA

NVE's ADL121-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V Typical Power Consumption 72 nW at 2.4 V 30 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycling Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL121-14E
Quantity in Stock:
11012

$5.15

ADL124-14E: 2.8 mT, 3V, 30 Hz Duty-Cycled GMR Switch, ULLGA

NVE's ADL124-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V Typical Power Consumption 72 nW at 2.4 V 30 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycling Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL124-14E
Quantity in Stock:
3117

$5.15

ADL921-14E: 2 mT, 3V Nanopower GMR Switch, ULLGA

NVE's ADL921-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing. Continuous operation allows high frequency operation. The part is packaged in an ultraminiature ULLGA. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 V to 4.2 V Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling 250 kHz Operating Frequency Digital Switch Output Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL921-14E

$5.15

ADL924-14E: 2.8 mT, 3V Nanopower GMR Switch, ULLGA

NVE's ADL924-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling 250 kHz Operating Frequency Digital Switch Output Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL924-14E
Quantity in Stock:
28150

$5.15

SM124-10E: General-Purpose 1 mT Smart GMR Magnetometer, TDFN6

The SM124-10E Smart Magnetometer combines an omnipolar GMR sensor element with with easy-to-use digital signal processing.

A digital output provides precise, programmable thresholds. An I²C interface provides magnetic field data, as well as a calibration interface. The device is factory calibrated for accuracy. Calibration coefficients are stored in internal nonvolatile memory.

All commands, data, and coefficients are a single byte, and a slick, elegant data structure lets you get up and running with a minimum of firmware.

Key features include:
  • Can detect magnets more than 50 mm away
  • I²C and digital threshold outputs
  • 0-1 mT linear range
  • 8-bit / 1% output resolution
  • −40°C to +125°C operating range
  • 5% FS accuracy for 0 to 85°C
  • 10 kSps sample rate for fast response
  • 6 mA typical supply current
  • In-plane sensitivity more usable than Hall effect sensors
  • Programmable offset and gain compensation
  • Optional magnet temperature compensation   • 2.2 to 3.6 volt supply
  • Ultraminiature 2.5 x 2.5 x 0.8 mm TDFN package

Part Number:
SM124-10E

$5.16

SM125-10E: General-Purpose 4 mT Smart GMR Magnetometer, TDFN6

The SM125-10E Smart Magnetometer combines an omnipolar GMR sensor element with with easy-to-use digital signal processing.

A digital output provides precise, programmable thresholds. An I²C interface provides magnetic field data, as well as a calibration interface. The device is factory calibrated for accuracy. Calibration coefficients are stored in internal nonvolatile memory.

All commands, data, and coefficients are a single byte, and a slick, elegant data structure lets you get up and running with a minimum of firmware.

Key features include:
  • Can detect magnets more than 50 mm away
  • I²C and digital threshold outputs
  • 0-4 mT linear range
  • 8-bit / 1% output resolution
  • −40°C to +125°C operating range
  • 5% FS accuracy for 0 to 85°C
  • 10 kSps sample rate for fast response
  • 6 mA typical supply current
  • In-plane sensitivity more usable than Hall effect sensors
  • Programmable offset and gain compensation
  • Optional magnet temperature compensation   • 2.2 to 3.6 volt supply
  • Ultraminiature 2.5 x 2.5 x 0.8 mm TDFN package

Part Number:
SM125-10E

$5.16

ABL004-10E: 1 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS TDFN

NVE's ABL004-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 1.0 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL004-10E
Quantity in Stock:
1162

$5.19

ABL005-10E: 0.5 mm, 1-Bridge Analog Gear-Tooth Sensor, TDFN

NVE's ABL005-10E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.5 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.500 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL005-10E
Quantity in Stock:
2396

$5.19

ABL006-10E: 0.3 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS TDFN

NVE's ABL006-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.3 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.300 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL006-10E
Quantity in Stock:
1172

$5.19

Displaying 81 to 100 (of 385 products)