AET100F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
AET120F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
AET500-02E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The half-bridge configuration maximizes noise immunity and provides large 300 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
NVE's AFL000-00E low power switch sensor integrates GMR sensor elements with digital
onboard signal processing electronics. The switch is designed for use in low power
and battery applications, and features supply voltages down to 0.9 Volts and
continuous operation at currents of 20-55 microamps. Like all NVE magnetic sensors,
the AFL sensors have extremely precise magnetic operate and release points.
Features:
Precision Magnetic Operate Point -- 10 Oersteds
Low Voltage -- 0.9 V
Low Power
Digital Output
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Single Battery Applications
Low Power, Low Field Applications
Supply
Voltage
min.-max.
Supply
Current
(µA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
0.9-1.3
20-55
7-13
1
0.4
Current Sink
PBBe
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
The AFL006-10E is the world's most sensitive magnetic switch. The switch is designed for use in low power
and battery applications. It can operate from a single cell with supplies as low as 0.9 V and typical supply current of 55 microamps.
Like all NVE magnetic
sensors, the AFL006-10E has extremely precise magnetic operate and release points.
Features:
4 Oe typical operate point for ultrahigh sensitivity
0.9 V – 2 V operating voltage for single-cell battery operation
Less than 100 microwatts power consumption
2.5 mm x 2.5 mm x 0.8 mm TDFN6 for miniaturization
Applications include:
Portable instruments
Utility meters
Noncontact overcurrent protection
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
NVE's AFL100-10E low power switch sensor integrates GMR sensor elements with digital
onboard signal processing electronics. Like all NVE magnetic
sensors, the AFL sensors have extremely precise magnetic operate and release points.
Features:
Precision Magnetic Operate Point -- 10 Oersteds (1 mT)
Low Power
Digital Output
Ultraminiature 2.5 mm x 2.5 mm TDFN Package
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
NVE's AFL200-00E low power switch sensor integrates GMR sensor elements with digital
onboard signal processing electronics. The switch is designed for use in low power
and battery applications, and features supply voltages down to 2.7 Volts
and continuous operation at currents of 20-55 microamps. Like all NVE magnetic
sensors, the AFL sensors have extremely precise magnetic operate and release points.
Features:
Precision Magnetic Operate Point -- 10 Oersteds
Normally OFF Current Sinking Digital Output
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Low Power Applications
Low Field Applications
Supply
Voltage
min.-max.
Supply
Current
(µA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
2.7-3.6
20-55
7-13
1
0.4
Current Sink
PBGe
Cross axis
MSOP8 (RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
The AG005-06 Printed Circuit Board is a 0.5 x 0.5 inch (13 x 13 mm) PCB with SOIC8 solder pads and through holes for wires or a connector. The PCB allows easy connections to AA-Series SOIC8 sensors (-02E suffix; order separately).
This PCB is also included in the AG001-01 Analog Sensor Evaluation Kit.
The AG035-06 Printed Circuit Board (PCB) is a 1.57 x 0.25 inch (40 x 6 mm) PCB for connection to 2.5 x 2.5 mm TDFN6 sensors (-10E suffix sensors; order sensors separately).
A 1.57 x 0.25 inch PCB for demonstrating ADLxxx-14E/AHLxxx-14E 1.1 x 1.1 mm ULLGA4 digital sensors (order sensors separately). In addition to space for the sensor, the boards have locations for 0402-size pull-up resistors and bypass capacitors.
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.
The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.
A 1.2 x 0.25 inch x 0.031 inch thick (30 x 6 x 0.75 mm) PCB for demonstrating 1.1 x 1.1 mm ULLGA4 sensors (-14E sensor suffix; order sensors separately).
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.