The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant.
A 3-volt coin cell (included) powers the board.
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
The AG952-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM124-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM124-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The AG960-07E provides easy connections to an SM324-10E Precision TMR Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM125-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The AG969-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a bus-bar for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The kit includes a demo board with three ultraminiature, ultralow-power ADL-Series magnetic sensors. Each sensor drives an indicator LED, and a meter shows the sensor power in microamps or nanoamps.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by a coin cell (included).
The AG953-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM225-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM225-10E sensor.
- a microcontroller connected to the sensor via SPI.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller.
The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration.
A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included.
The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.