A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.
$150.00
The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
$195.00
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$24.95
The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.
$65.00
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG952-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM124-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM124-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
$65.00
The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.
$90.00
The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
$19.95
The AG972-07E Demonstration Board showcases rotational encoding to
a few thousandths of a degree with an ABT375-00E sensor and a 30-tooth gear.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An ABT375-00E gear tooth sensor
An eight-digit rotational display
a 30-tooth. 0.5 module gear
Part #12216 ceramic bias magnet
Test points for analog outputs
Powered by two AAA batteries (included)
$195.00
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
$90.00
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
$75.00
The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.
$75.00
The AG960-07E provides easy connections to an SM324-10E Precision TMR Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
$60.00
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
$19.95
The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.
The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.
$75.00
The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.
$75.00
The AG953H-07 demonstrates high current measurement with the SM225-10E Smart TMR Magnetometer. A 1/4" x 1/2" busbar is mounted to the PCB, and the sensor can detect up to +/-650 amps. Based on the AG953-07E Evaluation Kit, a powerful, intuitive graphical user interface allows the user to control sensor offset, calibration, filtering, and memory.
$129.00
The AG956-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR002-10E Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR002-10E sensor
- a diametrical
magnet
- magnet fixturing and a
An interface board with:
- a microcontroller
connected to the sensor via SPI
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
$195.00