The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
$19.95
This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.
$75.00
A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".
$90.00
This self-contained module allows zeroing and programming the digital output threshold and hysteresis or SM124-10E or SM125-10E Smart Magnetometer without need of a computer or a customer microcontroller.
The 2.5" x 2.5" (64 mm x 64 mm) board has an I²C master microcontroller connected to the SM124.
A pushbutton for zeros the sensor, and miniature rotary thumbwheel switches provide three digits of resolution for the threshold and two for hysteresis. A custom TDFN-6 socket accommodates the 2.5 mm x 2.5 mm SM12x-10E. The module is powered by a small wall-mounted power supply (included).
Jumpers allow the sensor to be disconnected from the rest of the board so the board can be used as an interface to the customer’s electronics.
This module includes:
A 2.5 x 2.5 mm TDFN6 socket for a SM12x-10E Smart Magnetometer
A preprogrammed, onboard microcontroller
Two sets of thumbwheel switches for digital threshold and hysteresis
Two LEDs indicating the sensor’s output and successful programming
A 5-volt wall-mount power supply
Sensors are sold separately.
$195.00
The AG957-07E provides easy connections to an ASR002-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$24.95
The AG960-07E provides easy connections to an SM324-10E Precision TMR Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
$19.95
The AG970-07E Evaluation Kit helps test a variety AET-Series sensors with linear magnetic scales. The kit includes:
All five AET-Series parts (unsoldered in tubes)
A 3 x 4-inch (76 x 101 mm) PCB with test points and screw terminals
Detachable fixturing for linear magnetic tape (tape sold separately)
$65.00
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
$50.00
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
$19.95
The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.
Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.
$195.00
The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.
$75.00
The AG954-07E provides a socket for easy programming and prototyping of TDFN6 devices without soldering and unsoldering.
The custom socket is compatible with NVE's 2.5 mm x 2.5 mm TDFN6 package parts (-10E suffixes).
The board is 1.5" x 2" (38 mm x 50 mm), and uses brass hardware to minimize magnetic interference with the socketed sensor.
A 0.1"-spaced header provides for connections to the sensors, and a row of 0.1"-spaced through-holes allows for auxiliary parts such as a decoupling capacitor or an LED.
$129.00
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00
The AG953H-07 demonstrates high current measurement with the SM225-10E Smart TMR Magnetometer. A 1/4" x 1/2" busbar is mounted to the PCB, and the sensor can detect up to +/-650 amps. Based on the AG953-07E Evaluation Kit, a powerful, intuitive graphical user interface allows the user to control sensor offset, calibration, filtering, and memory.
$129.00
The AG964-07E Demonstation Board has everything you need to evaluate
the remarkable ASR022-10E ABZ TMR Encoder Sensor. The demonstration includes:
ASR022-10E ABZ Noncontact TMR Encoder Sensor
A four-digit display to indicate rotation
Part # 12426 split-pole Alnico 5 round horseshoe magnet
LEDs for A, B, Z, and Direction outputs
Plastic magnet locating fixture
Powered by two AAA batteries (included)
$195.00
This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller. The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration. A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included. The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.
$150.00
The AG953-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM225-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM225-10E sensor.
- a microcontroller connected to the sensor via SPI.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00