Sensor Evaluation Kits
AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040C
- Quantity in Stock:
- 28
$16.95
AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040B
- Quantity in Stock:
- 31
$19.95
AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board
The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040T
$19.95
AG957-07E: ASR002 Smart TMR Angle Sensor breakout board
The AG957-07E provides easy connections to an ASR002-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG957-07E
- Quantity in Stock:
- 7
$19.95
AG959-07E: SM225 High-Speed Smart TMR Magnetometer breakout board
The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG959-07E
- Quantity in Stock:
- 5
$19.95
AG960-07E: SM324 Ultraprecise Smart Magnetometer breakout board
The AG960-07E provides easy connections to an SM324-10E Precision TMR Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG960-07E
- Quantity in Stock:
- 9
$19.95
AG966-07E: ASR012 I2C/PWM Smart TMR Angle Sensor breakout board
The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG966-07E
- Quantity in Stock:
- 2
$19.95
AG967-07E: ASR022 ABZ Smart TMR Encoder Sensor breakout board
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG967-07E
- Quantity in Stock:
- 14
$19.95
AG968-07E: SM228 15 mT I2C Smart TMR Magnetometer Breakout Board
The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG968-07E
- Quantity in Stock:
- 2
$19.95
AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG975-07E
$19.95
AG977-07E: ASR003 Smart TMR Angle Sensor breakout board
The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG977-07E
- Quantity in Stock:
- 4
$19.95
ALT021-10E-EVB01: 0-0.25 mT TMR magnetometor eval board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
- Part Number:
- ALT021-10E-EVB01
- Quantity in Stock:
- 8
$19.95
ALT023-10E-EVB01: 0-1 mT TMR magnetometor eval board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
- Part Number:
- ALT023-10E-EVB01
- Quantity in Stock:
- 10
$19.95
ALT025-10E-EVB01: 0-10 mT DFN6 TMR magnetometor eval board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
- Part Number:
- ALT025-10E-EVB01
- Quantity in Stock:
- 10
$19.95
ALT025-14E-EVB01: 0-10 mT DFN4 TMR magnetometor eval board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
- Part Number:
- ALT025-14E-EVB01
- Quantity in Stock:
- 10
$19.95
AG958-07E: SM124 Smart GMR Magnetometer breakout board w/connector
The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG958-07E
- Quantity in Stock:
- 11
$24.95
AG961-07E: SM125 Smart GMR Magnetometer breakout board w/connector
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG961-07E
- Quantity in Stock:
- 22
$24.95
AG974-07E: ACT001-10E Isolated Current Sensor Evaluation Board
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
- Part Number:
- AG974-07E
- Quantity in Stock:
- 20
$50.00
AG001-01E: GMR Analog Sensor Evaluation Kit
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
- Part Number:
- AG001-01E
- Quantity in Stock:
- 4
$60.00
AG911-07E: GMR Switch Evaluation Kit
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
- Part Number:
- AG911-07E
- Quantity in Stock:
- 11
$65.00
