This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
The AG960-07E provides easy connections to an SM324-10E Precision TMR Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT026-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.