A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".
The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.
The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.
The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.
The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.