A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.
The board can be powered by a 0.9 to 7 V supply or battery and provides a linear, single-ended output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT002-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AKT001-14E high-field (1.5 T), low power TMR analog bridge magnetometer. The sensor is an ultraminiature 1.1 x 1.1 mm package.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides a differential output voltage proportional to the applied magnetic field.
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The AG972-07E Demonstration Board showcases rotational encoding to
a few thousandths of a degree with an ABT375-00E sensor and a 30-tooth gear.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An ABT375-00E gear tooth sensor
An eight-digit rotational display
a 30-tooth. 0.5 module gear
Part #12216 ceramic bias magnet
Test points for analog outputs
Powered by two AAA batteries (included)
The AG970-07E Evaluation Kit helps test a variety AET-Series sensors with linear magnetic scales. The kit includes:
All five AET-Series parts (unsoldered in tubes)
A 3 x 4-inch (76 x 101 mm) PCB with test points and screw terminals
Detachable fixturing for linear magnetic tape (tape sold separately)
The AG969-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a bus-bar for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
The AG963-07E Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR012-10E I2C Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR012-10E sensor
- a diametrical
magnet
- magnet fixturing
An interface board with:
- a microcontroller
connected to the sensor via I²C
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM125-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The AG957-07E provides easy connections to an ASR002-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AG956-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR002-10E Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR002-10E sensor
- a diametrical
magnet
- magnet fixturing and a
An interface board with:
- a microcontroller
connected to the sensor via SPI
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
This self-contained module allows zeroing and programming the digital output threshold and hysteresis or SM124-10E or SM125-10E Smart Magnetometer without need of a computer or a customer microcontroller.
The 2.5" x 2.5" (64 mm x 64 mm) board has an I²C master microcontroller connected to the SM124.
A pushbutton for zeros the sensor, and miniature rotary thumbwheel switches provide three digits of resolution for the threshold and two for hysteresis. A custom TDFN-6 socket accommodates the 2.5 mm x 2.5 mm SM12x-10E. The module is powered by a small wall-mounted power supply (included).
Jumpers allow the sensor to be disconnected from the rest of the board so the board can be used as an interface to the customer’s electronics.
This module includes:
A 2.5 x 2.5 mm TDFN6 socket for a SM12x-10E Smart Magnetometer
A preprogrammed, onboard microcontroller
Two sets of thumbwheel switches for digital threshold and hysteresis
Two LEDs indicating the sensor’s output and successful programming
The AG954-07E provides a socket for easy programming and prototyping of TDFN6 devices without soldering and unsoldering.
The custom socket is compatible with NVE's 2.5 mm x 2.5 mm TDFN6 package parts (-10E suffixes).
The board is 1.5" x 2" (38 mm x 50 mm), and uses brass hardware to minimize magnetic interference with the socketed sensor.
A 0.1"-spaced header provides for connections to the sensors, and a row of 0.1"-spaced through-holes allows for auxiliary parts such as a decoupling capacitor or an LED.
The AG953H-07 demonstrates high current measurement with the SM225-10E Smart TMR Magnetometer. A 1/4" x 1/2" busbar is mounted to the PCB, and the sensor can detect up to +/-650 amps. Based on the AG953-07E Evaluation Kit, a powerful, intuitive graphical user interface allows the user to control sensor offset, calibration, filtering, and memory.