The IL613-3E is a 3.3/5V, 3-channel (2 transmit, 1 receive), 100 Mbps isolated signal coupler with CMOS outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop GMR Sensor technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 16-pin 0.3" SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The IL3685 is an isolated 40 Mbps RS-485 transceiver with an extended temperature range. Over-temperature protection; fully PROFIBUS compliant; 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
Galvanically-isolated high-speed RS-485 differential bus transceiver with 2500 Vrms isolation, 2 kV Bus ESD, and 20 kV/microsecond transient immunity. The IL 485 has a 35 Mbd data rate and is Profibus recognized. Available in a 0.3"-wide 16-pin SOIC package.
The IL015E is a low-power, 3.3/5V, 10 Mbps, 100C Isolator. Typical total quiescent current is just 0.3 mA per channel. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The ILDC11VE is a miniature, one-quarter watt fully-regulated 3.3V-to-3.3V DC-DC convertor. The part can be used to generate an isolated 3.3-volt bus supply from a controller supply.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 6 kV isolation and virtually unlimited barrier life.
The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
The IL41050TT is a low-cost, basic CAN transceiver without Vref output and silent mode input pins. 2.5kV isolation; 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic.
16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
The IL3085TE is an isolated 4 Mbps RS-485 transceiver with an extended temperature range. Compatible with 3.3 V or 5 V input logic. 16-pin wide-body SOIC package with True 8™ mm creepage.
The IL016E is a low-power, 3.3/5V, 10 Mbps, 100C Isolator. Typical total quiescent current is just 0.3 mA per channel. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The RS-485 Wide-Body Isolator Evaluation Board provides a complete isolated RS-485 node using the popular 0.3" (8 mm) creepage IL3585E isolated transceiver. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
These 2 x 3.5-inch (50 x 90 mm) boards include an IL3685TE isolated RS-485 transceiver,
a termination resistors, power-supply bypass capacitors as recommended, screw
connections, provisions for header pins, and a DB9 bus connector for PROFIBUS.
The IL3685TE is the world's fastest isolated transceiver with data rates to 40 Mbps, is fully PROFIBUS compatible, including the stringent bus differential specifications, and is rated to a full 125C.
The isolated CAN Evaluation Board provides a complete isolated Controller Area Network node using NVE's popular IL41050TAE isolated wide-body CAN transceiver with true 8mm creepage.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL715E four-channel (all the same direction) wide-body isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The boards let you evaluate the world's best isolators.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL715VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL716E four-channel (two each direction) wide-body isolator, two bypass capacitors as recommended, screw connections, test pads, and header pins.
The boards let you evaluate the world's best isolators.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL716VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL717VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.