AET075F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
AET100F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
AET120F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
The AG919-06 is a 2 x 0.25 inch (50 x 6 mm) PCB designed to be used with MSOP8 sensors (-00E package; order sensors separately). The MSOP8 is rotated 90 degrees compared to the AG918-06.
NVE's DB001-00E signal processing IC is designed to work with NVE's AD9xx series GMR switch with short circuit protection. This combination provides a high-current switched output that corresponds to the sensor input. The DB001-00E functions as the front end of a complete sensor assembly, and includes protection against short circuits and high voltage transients from capacitive and inductive loads. The parts also feature thermal shutdown circuitry and reverse battery protection. They provide a regulated output voltage for the sensor and other components in the assembly, and an LED driver to indicate an "ON" condition.
Features:
High Current Output
Reverse Battery and Transient Protection
LED Driver
Excellent Temperature and Voltage Performance
Small, Low Profile Surface Mount Packages
Note: Parts must be purchased in multiples of 100 when purchased in quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The IL510-1 is a 3.3V/5V, single-channel, 2 Mbps DC-correct digital isolator, with optional external synchronization clock, output enable, 25 ns propagation delay, 10 ns pulse width distortion with 1 kVrms isolation and 20 kV/microsecond transient immunity, -40°C to 85°C. Unique 8-pin MSOP.
The "E" suffix indicates this part is lead (Pb) free.
The IL511-1 is a 3.3V/5V, dual-channel unidirectional 2 Mbps DC-correct digital isolator, 25 ns propagation delay, 10 ns pulse width distortion with 1 kVrms isolation and 50 kV/microsecond typical transient immunity, -40°C to 85°C. Unique 8-pin MSOP.
The "E" suffix indicates this part is lead (Pb) free.
The IL610-1E is a 3.3/5V, single-channel, 100 Mbps isolated signal coupler with a CMOS output, which can be used to replace opto-couplers in many standard isolation functions. The device is manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged coupler).
This part is lead (Pb) free.
Lead-free
product information
The IL610A-1E is a 3.3/5V, single-channel, 10 Mbps isolated signal coupler with an open-drain output, which can be used to replace opto-couplers in many standard isolation functions. The device is manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged coupler).
This part is lead (Pb) free.
Lead-free
product information
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL610CMTI-1E is a single-channel version in an ultraminiature MSOP8 package.
The IL611-1E is a 3.3/5V, dual-channel, 100 Mbps isolated signal coupler with CMOS outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged couplers).
This part is lead (Pb) free.
Lead-free
product information
The IL611A-1E is a 3.3/5V, dual channel, 10 Mbps isolated signal coupler with open-drain outputs, which can be used to replace opto-couplers in many standard isolation functions. The devices are manufactured with NVE's IsoLoop spintronic GMR technology giving exceptional small size and low power dissipation. The passive input structure allows direct interface to a very wide range of voltage inputs. A single resistor is used to set maximum current for input voltages above 0.5 V. 20 kV/microsecond transient immunity. 8-pin MSOP package (the world's smallest packaged couplers).
This part is lead (Pb) free.
Lead-free
product information
IL6xxCMTI-Series isolators are
optimized for driving MOSFETs either directly or with an
external gate driver.
Resistors set the input current, and five milliamps guarantees
switching. The inputs can be configured as non-inverting or
inverting.
CMTI-grade isolators are 100% tested to ensure each part has
at least 200 kV/µs minimum Common-Mode Transient
Immunity. Simple external deglitch circuitry can extend the
CMTI to an extraordinary 350 kV/µs typical.
The parts also have an extended supply range of up to 6.6 volts
for compatibility to directly drive a range of power
MOSFETs or gate driver ICs. The parts provide full 2.5 kV isolation.
The IL611CMTI-1E is a two-channel version in an ultramniature MSOP8 package.
The IL710-1 is a 3.3V/5V, single channel, 110 Mbps CMOS-compatible isolated buffer, with enable, 10 ns propagation delay, 3 ns pulse width distortion with 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package.
This part is lead (Pb) free.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL710S-1E 150 Mbps single-channel (all the same direction) ultraminiature MSOP8 isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The board lets you evaluate the world's smallest isolators.
The IL710S-1 is a 3.3V/5V, single channel, 150 Mbps CMOS-compatible isolated buffer, with enable, 10 ns propagation delay, 300 ps pulse width distortion with 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package.
This part is lead (Pb) free.
The IL710T-1 is a high temperature, 3.3/5V, single channel, 110 Mbps, CMOS compatible, isolated buffer with automatic level shifting, output enable, 10 ns propagation delay, 3 ns pulse width distortion, 1 kVrms isolation and 20 kV/microsecond transient immunity. Unique 8-pin MSOP package.
The "E" suffix indicates this part is lead (Pb) free.