A machined-aluminum magnet holder for 8 mm dia. magnets such as part numbers 12527 and 12528 (sold separately).
Compatible with
AG93x-Series
and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.
Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.
$70.00
A machined-aluminum magnet holder for 4 mm dia. magnets such as part number 12526 (sold separately).
Compatible with
AG93x-Series
and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.
Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.
$70.00
The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.
$70.00
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
$75.00
The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.
$90.00
The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.
$75.00
The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.
$75.00
This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller. The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration. A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included. The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.
$150.00