Products meeting the search criteria
AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit
The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.
The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.
- Part Number:
- AG903B-07E
$75.00
AG933-07E: AAT009 6 MOhm Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.
- Part Number:
- AG933-07E
$75.00
AG976-07E: ASR003-10E Smart SPI Angle Sensor Evaluation Kit
The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.
Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.
- Part Number:
- AG976-07E
$195.00
IL41050-1-01: QSOP Isolated CAN Evaluation Board
The QSOP isolated CAN Evaluation Board provides a complete isolated Controller Area Network node using the world's smallest isolated CAN transceiver, the IL41050TA-1E.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
- Part Number:
- IL41050-1-01
$49.95
AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.
- Part Number:
- AG934-07E
- Quantity in Stock:
- 1
$75.00
IL700-01: IL700-Series Isolator Evaluation Board
This evaluation board lets you try a variety of NVE’s flagship series of award-winning of IsoLoop Isolators.
The board has four IL700-Series isolators in four package types:
• IL716E (wide-body SOIC-16)
• IL715-3E (narrow-body SOIC-16)
• IL712-3E (SOIC-8)
• IL710S-1E (MSOP-8)
IL700-Series Isolators use patented spintronic Giant Magnetoresistive (GMR) technology. The symmetric magnetic coupling barrier provides a typical propagation delay of only 10 ns and a pulse width distortion as low as 300 ps, the best of any isolator. And their real ceramic/polymer barriers last pretty much forever.
- Part Number:
- IL700-01
- Quantity in Stock:
- 1
$49.95
AG953-07E: SM225-10E Smart TMR Magnetometer Evaluation Kit
The AG953-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM225-10E Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM225-10E sensor.
- a microcontroller connected to the sensor via SPI.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG953-07E
- Quantity in Stock:
- 3
$95.00
IL3085-1-01: RS-485 QSOP Isolator Evaluation Board
The RS-485 QSOP Isolated Transceiver Evaluation Board provides a complete isolated RS-485 node using the world's isolated transceiver, the IL3085-1E. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
Isolating RS-485 nodes reduces noise, eliminates ground loops, and improves safety.
- Part Number:
- IL3085-1-01
- Quantity in Stock:
- 3
$74.95
AG962-07E: SM125-10E Smart GMR Magnetometer Evaluation Kit
The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM125-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG962-07E
- Quantity in Stock:
- 4
$95.00
AG969-07E: SM228-10E Smart I²C TMR Magnetometer Evaluation Kit
The AG969-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a bus-bar for evaluating as a current sensor.
• An LED indicating the state of the threshold output.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG969-07E
- Quantity in Stock:
- 4
$95.00
IL3585-01: RS-485 Wide-Body Isolator Evaluation Board
The RS-485 Wide-Body Isolator Evaluation Board provides a complete isolated RS-485 node using the popular 0.3" (8 mm) creepage IL3585E isolated transceiver. The board provides screw terminal and RJ45 connections, and demonstrates best layout practices.
Termination, pull-up, and pull-down resistors are easily changed to accommodate various fanouts and termination methods.
The transceiver delivers an exceptional 2.3 V differential output into a 54 Ohm load and data rates to 40 Mbps. The device is also compatible with 3.3 V input supplies, allowing interface to standard microcontrollers without additional level shifting.
Isolating RS-485 nodes reduces noise, eliminates ground loops, and improves safety.
- Part Number:
- IL3585-01
- Quantity in Stock:
- 4
$74.95
IL41050WB-01: Isolated Wide-Body CAN Evaluation Board
The isolated CAN Evaluation Board provides a complete isolated Controller Area Network node using NVE's popular IL41050TAE isolated wide-body CAN transceiver with true 8mm creepage.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
- Part Number:
- IL41050WB-01
- Quantity in Stock:
- 4
$49.95
IL600-01: IL600-Series Isolator Evaluation Board
The IL600-Series Isolator evaluation board lets you try a variety of NVE’s unique passive-input isolators.
The board has four IL600-Series isolators in four package types:
• IL613E (wide-body SOIC-16)
• IL614-3E (narrow-body SOIC-16)
• IL611-3E (SOIC-8)
• Open-drain IL610A-1E (MSOP-8)
A pushbutton and LED demonstrates the unmatched flexibility of these devices.
The award-winning IL600 and IL600A Series Isolators provide unique flexibility similar to LED-input optocouplers but with better performance and higher package density.
- Part Number:
- IL600-01
- Quantity in Stock:
- 4
$49.95
IL700-1-01: QSOP 4- and 5-Channel Isolator Evaluation Board
This evaluation board lets you try the world’s densest high-performance isolators.
The board includes five high-performance QSOP isolators:
- IL715-1E: 4-Channel (all same direction)
- IL716-1E: 4-Channel (2 each direction)
- IL717-1E: 4-Channel (3 transmit, 1 receive)
- IL260-1E: 5-Channel (all same direction)
- IL261-1E: 5-Channel (4 transmit, 1 receive)
IsoLoop QSOP isolators have best-in-class performance:
- 110 Mbps
- 2500 V isolation
- -40°C to +100°C
- 3 V to 5.5 V operation
- 44000 year barrier life
- True 4 mm creepage
- Part Number:
- IL700-1-01
- Quantity in Stock:
- 4
$49.95
AG001-01E: GMR Analog Sensor Evaluation Kit
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
- Part Number:
- AG001-01E
- Quantity in Stock:
- 5
$60.00
AG973-07E: SM223-10E Smart I²C TMR Magnetometer Evaluation Kit
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• An LED indicating the state of the threshold output.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG973-07E
- Quantity in Stock:
- 7
$95.00
AG920-07E: GT Sensor Evaluation Kit
The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.
- Part Number:
- AG920-07E
- Quantity in Stock:
- 8
$65.00
IL41050-01: Narrow-Body Isolated CAN Evaluation Board
The CAN Evaluation Board provides a complete isolated Controller Area Network node using the popular IL41050TA-3E isolated narrow-body isolated CAN transceiver.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, and pull-up resistors.
- Part Number:
- IL41050-01
- Quantity in Stock:
- 9
$49.95
AG910-07E: GMR Switch Evaluation Kit w/ZIF socket
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
- Part Number:
- AG910-07E
- Quantity in Stock:
- 10
$90.00
AG952-07E: SM124-10E Smart GMR Magnetometer Evaluation Kit
The AG952-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM124-10E Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM124-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG952-07E
- Quantity in Stock:
- 10
$95.00
