Products meeting the search criteria
AAT001-10E-EVB01: 1.25 MOhm TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
- Part Number:
- AAT001-10E-EVB01
- Quantity in Stock:
- 29
$19.95
AAT003-10E-EVB01: 40 kOhm TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
- Part Number:
- AAT003-10E-EVB01
- Quantity in Stock:
- 28
$19.95
AAT006-10E-EVB01: 1.5 mT TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
- Part Number:
- AAT006-10E-EVB01
- Quantity in Stock:
- 29
$19.95
AAT009-10E-EVB01: 6 MOhm TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
- Part Number:
- AAT009-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AAT101-10E-EVB01: Full-Bridge TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
- Part Number:
- AAT101-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AG004-06: SOIC8 Printed Circuit Board (3" x 0.3")
A 3 x 0.3 inch (76 x 8 mm) PCB to demonstrate AA-Series SOIC sensors (-02E suffix; order sensors separately).
This PCB is also included in the AG001-01 Sensor Evaluation Kit.
- Part Number:
- AG004-06
- Quantity in Stock:
- 1317
$4.25
AG005-06: SOIC8 Printed Circuit Board (0.5" square)
The AG005-06 Printed Circuit Board is a 0.5 x 0.5 inch (13 x 13 mm) PCB with SOIC8 solder pads and through holes for wires or a connector. The PCB allows easy connections to AA-Series SOIC8 sensors (-02E suffix; order separately).
This PCB is also included in the AG001-01 Analog Sensor Evaluation Kit.
- Part Number:
- AG005-06
- Quantity in Stock:
- 627
$2.25
AG035-06: TDFN6 Printed Circuit Board
The AG035-06 Printed Circuit Board (PCB) is a 1.57 x 0.25 inch (40 x 6 mm) PCB for connection to 2.5 x 2.5 mm TDFN6 sensors (-10E suffix sensors; order sensors separately).
- Part Number:
- AG035-06
- Quantity in Stock:
- 786
$4.25
AG039-06: ULLGA Digital Sensor Demonstration Bare Board
A 1.57 x 0.25 inch PCB for demonstrating ADLxxx-14E/AHLxxx-14E 1.1 x 1.1 mm ULLGA4 digital sensors (order sensors separately). In addition to space for the sensor, the boards have locations for 0402-size pull-up resistors and bypass capacitors.
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
- Part Number:
- AG039-06
- Quantity in Stock:
- 465
$5.00
AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040B
- Quantity in Stock:
- 31
$19.95
AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040C
- Quantity in Stock:
- 27
$16.95
AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board
The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040T
$19.95
AG915-06: MSOP8 Printed Circuit Board (0.25" octagonal)
A 0.25-inch (6 mm) octagonal PCB for easy connections to MSOP8 sensors (-00E suffix; order sensors separately).
The PCB provides through holes for #28 or #30 wires.
- Part Number:
- AG915-06
- Quantity in Stock:
- 822
$2.25
AG918-06: MSOP8 Printed Circuit Board (2" x 0.25")
A 2 x 0.25 inch (50 x 6 mm) PCB designed to be used with MSOP8 sensors (-00E package; purchase sensors separately).
This PCB is also included in the AG910-07 and AG911-07 Sensor Evaluation Kits.
- Part Number:
- AG918-06
- Quantity in Stock:
- 556
$4.25
AG935-07E: 60-LED "Blinky" AAT003 Angle Sensor Demo Board
This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller. The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration. A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included. The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.
- Part Number:
- AG935-07E
- Quantity in Stock:
- 2
$150.00
AG941-07E: ADL-Series Sensor Demo Board
The kit includes a demo board with three ultraminiature, ultralow-power ADL-Series magnetic sensors. Each sensor drives an indicator LED, and a meter shows the sensor power in microamps or nanoamps. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by a coin cell (included).
- Part Number:
- AG941-07E
- Quantity in Stock:
- 3
$90.00
AG954-07E: TDFN6 Socket Board
The AG954-07E provides a socket for easy programming and prototyping of TDFN6 devices without soldering and unsoldering.
The custom socket is compatible with NVE's 2.5 mm x 2.5 mm TDFN6 package parts (-10E suffixes).
The board is 1.5" x 2" (38 mm x 50 mm), and uses brass hardware to minimize magnetic interference with the socketed sensor.
A 0.1"-spaced header provides for connections to the sensors, and a row of 0.1"-spaced through-holes allows for auxiliary parts such as a decoupling capacitor or an LED.
- Part Number:
- AG954-07E
$129.00
AG957-06E: Bare breakout board for ASR0xx Smart Angle Sensors
The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG957-06E
- Quantity in Stock:
- 11
$2.25
AG958-07E: SM124 Smart GMR Magnetometer breakout board w/connector
The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG958-07E
- Quantity in Stock:
- 5
$24.95
AG959-07E: SM225 High-Speed Smart TMR Magnetometer breakout board
The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG959-07E
- Quantity in Stock:
- 3
$19.95
