New Products

Displaying 81 to 100 (of 443 products)
ADL125-14E: 1 mT, 3V, 30 Hz Duty-Cycled GMR Switch, DFN4

NVE's ADL125-14E Ultrasensitive Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultrasensitive 1 mT operate point Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm DFN4 package 2.4 to 4.2 V Typical Power Consumption 72 nW at 2.4 V 30 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycling Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL125-14E
Quantity in Stock:
500

$5.63

ADL925-14E: 1 mT, 3V Nanopower GMR Switch, DFN4

NVE's ADL925-14E Ultrasensitive Nanopower Switch integrates GMR sensor elements with digital onboard signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: Ultrasensitive 1 mT operate point Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm DFN4 package 2.4 to 4.2 V Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling 250 kHz Operating Frequency Digital Switch Output Applications: Battery-Powered Devices Portable Instruments

Part Number:
ADL925-14E
Quantity in Stock:
7190

$5.63

IL3685TE: 40 Mbps Isolated RS485 Transceiver, 125C, 2.5kV, Wide SOIC

The IL3685 is an isolated 40 Mbps RS-485 transceiver with an extended temperature range. Over-temperature protection; fully PROFIBUS compliant; 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL3685TE
Quantity in Stock:
698

$6.07

IL3085TE: 4 Mbps Isolated RS485 Transceiver, 125C, 2.5kV, Wide SOIC

The IL3085TE is an isolated 4 Mbps RS-485 transceiver with an extended temperature range. Compatible with 3.3 V or 5 V input logic. 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL3085TE
Quantity in Stock:
85

$5.56

SHIELD01-01: 40V/50A H-Bridge Arduino Shield Eval Board

This Arduino Shield board implements an H-bridge power converter using four power MOSFETs, four IL610CMTI-1E ultrahigh CMTI isolated MOSFET drivers, and two ILDC13-15E ultraminiature isolated DC-to-DC convertors.

The board is rated for 40 volts and 50 amps, to control up to two-kilowatt loads.

Example programs are available via our GitHub Repository.

Key features of the board are:
  • A Simple three-wire Arduino interface (PWM, Dir, and Enable)
  • Heat-sinking and thermal vias
  • Standard Arduino Shield form factor outline
  • Easy connections with large screw terminals

Specifications:
  • Max. load: 2 kW (40 V / 50 A)
  • Load supply line: 8 to 40 V
  • Arduino input supply: 5V or 7 V to 20 V, 500 mA max.
  • Logic-to-load isolation: 2.5 kV per UL 1577
  • Operating Temperature Range: -40 °C to 85 °C
  • Dimensions: 2.1 in. by 2.7 in. (53.4 mm by 68.6 mm)

Applications:
  • Motor speed and direction control
  • Robotics
  • DC-to-AC invertors

Part Number:
SHIELD01-01
Quantity in Stock:
17

$195.95

IL7817V-01: Isolated 4-Ch SPI w/Integ DC-DC Conv Eval Board

This Evaluation Board provides a complete isolated four-channel SPI node, plus an isolated 3.3 V to 5 V DC-to-DC convertor using an IL7817VE.

The board provides screw terminals for connections, plus test points for checking voltages and I/O. There are also LEDs to indicate DC-to-DC convertor input and output power. It uses a 2s2p board with thermal vias for optimal thermal performance.

The IL7817V is a high-speed, fully-isolated, data couplers with an integrated, one-quarter watt 3.3 V to 5 V DC-to-DC boost convertor. This level of integration dramatically reduces chip count and board area.

Part Number:
IL7817V-01
Quantity in Stock:
50

$84.95

ILDC13V-01: Isolated 3.3-to-6V SOIC16 DC-DC Conv Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating. The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired. The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC13V-01
Quantity in Stock:
50

$84.95

ILDC12V-01: Isolated 3.3-to-5V SOIC16 DC-DC Conv Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating. The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired. The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC12V-01
Quantity in Stock:
50

$84.95

ILDC11V-01: Isolated 3.3-to-3.3V SOIC16 DC-DC Conv Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating.

The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.

The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC11V-01
Quantity in Stock:
50

$84.95

ILDC12V-15-01: Isolated 3.3-to-5V DFN6 DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-5 V version of world’s smallest isolated DC-to-DC convertor, the ILDC12-15E.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC12V-15E is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC12V-15-01
Quantity in Stock:
50

$84.95

ALT021-10E: 0-0.25 mT TMR Bipolar Analog Sensor, 20 KOhm, x-axis, TDFN6

The ALT021 is an ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. Features: ±0.25 mT linear range Ultrahigh sensitivity (500 mV/V/mT typical) Large output signal (200 mV/V/mT typical) 0 - 10 V power supply Wheatstone bridge magnetometer configuration 20 kiloohm device resistance for low power Up to 300 kHz frequency bandwidth 2.5 x 2.5 mm TDFN6 package –40 to 125°C Applications: Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
Navigation

Part Number:
ALT021-10E
Quantity in Stock:
9300

$12.00

ADT005-10E: High Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6

ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.

The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.

To minimize power, the ADT005 does not include the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.

The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.

The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.

Part Number:
ADT005-10E
Quantity in Stock:
100

$11.18

AG957-06E: Bare breakout board for ASR0xx Smart Angle Sensors

The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG957-06E
Quantity in Stock:
11

$2.25

IL7816VE: 4-channel (2 each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7816VE is a four-channel (two each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7816VE
Quantity in Stock:
22

$12.40

IL7817VE: 4-channel (3 transmit, 1 receive) Isolator w/3.3-5V DC-DC Convertor

The IL7817VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7817VE

$12.40

IL7815VE: 4-channel (all same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7815VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7815VE
Quantity in Stock:
9

$12.40

IL7814VE: 3-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7814VE is a three-channel (2 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7814VE
Quantity in Stock:
16

$11.78

IL7812VE: Two-channel (one each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7812VE is a two-channel (one each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7812VE
Quantity in Stock:
18

$11.16

IL7811VE: Two-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor

The IL7811VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7811VE

$11.16

ILDC12VE: 6 kV Isolation 1/4W 3.3-to-5V DC-DC Conv Wide SOIC

The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.

NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 6 kV isolation and virtually unlimited barrier life.

The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.

The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.

Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.

Part Number:
ILDC12VE

$5.98

Displaying 81 to 100 (of 443 products)