New Products
IL7811VE: Two-channel (both same direction) Isolator w/3.3-5V DC-DC Convertor
The IL7811VE is a two-channel (both the same direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.
The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.
6 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.
- Part Number:
- IL7811VE
$11.16
ILDC12VE: 6 kV Isolation 1/4W 3.3-to-5V DC-DC Conv Wide SOIC
The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 6 kV isolation and virtually unlimited barrier life.
The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
- Part Number:
- ILDC12VE
- Quantity in Stock:
- 3
$5.98
ILDC12-15E: Isolated 1/4W 3.3-to-5V DC-DC Conv, 1kV, DFN6
The ILDC12-15E is a one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated RS-485 bus supplies, or power high-side gate supplies in H-bridges.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide 1 kV isolation and virtually unlimited barrier life.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
- Part Number:
- ILDC12-15E
$5.43
ILDC13VE: 6 kV Isolation 1/4W 3.3-to-6V DC-DC Conv Wide SOIC
The ILDC13VE is a miniature, one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor. The part can be used to generate isolated high-side gate supplies for H-bridges.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide best-in-class 6 kV isolation and virtually unlimited barrier life.
The unique True-8(TM) package provides true eight-millimeter creepage in accordance with IEC60601. Maximum 5 mV peak-to-peak ripple means low noise.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
- Part Number:
- ILDC13VE
$5.98
ILDC13-15E: Isolated 1/4W 3.3-to-6V DC-DC Conv, 1 kV, DFN6
The ILDC13-15E is a one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The part can be used to generate isolated high-side gate supplies for H-bridges.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide 1 kV isolation and virtually unlimited barrier life.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
- Part Number:
- ILDC13-15E
$5.43
AG976-07E: ASR003-10E Smart SPI Angle Sensor Evaluation Kit
The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.
Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.
- Part Number:
- AG976-07E
$195.00
AG977-07E: ASR003 Smart TMR Angle Sensor breakout board
The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG977-07E
$19.95
AG973-07E: SM223-10E Smart I²C TMR Magnetometer Evaluation Kit
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• An LED indicating the state of the threshold output.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG973-07E
- Quantity in Stock:
- 7
$95.00
AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG975-07E
$19.95
AG974-07E: ACT001-10E Isolated Current Sensor Evaluation Board
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
- Part Number:
- AG974-07E
- Quantity in Stock:
- 19
$50.00
AAH002-02E PCBA: Ultrahigh Sensitivity Analog Sensor Assembly
A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.
- Part Number:
- AAH002-02E PCBA
- Quantity in Stock:
- 27
$150.00
IL810T-3E: Single Channel Top-of-the-Line Isolator, 2.5 kV, SOIC8
The IL810T-3E is NVE's top-of-the-line single-channel isolator, with best-in-class specifications:
• 125 °C max. operating temperature
• 110 Mbps
• 10 ns propagation delay
• DC-correct; deterministic power-up
• 50 kV/µs typ.; 30 kV/µs min. transient immunity
• IEC 60747-5-5 (VDE 0884) certified—600 Vrms WV
• 44000-year barrier life
• Low EMC footprint
The part is an 8-pin SOIC RoHS package.
- Part Number:
- IL810T-3E
- Quantity in Stock:
- 1315
$3.93
SM223-10E: High-Speed Smart TMR Magnetometer, 1.5mT, I2C, TDFN6
The SM223-10E Smart Magnetometer combines a Tunneling Magnetoresistance (TMR) sensor element with
sophisticated digital signal processing for a unique combination of speed and precision. An I2C interface provides data as well as an external programming interface, and allows setting a versatile digital threshold output.
Unlike awkward, old-fashioned Hall-effect sensors, TMR is sensitive in-plane for
optimal current sensing and easy mechanical interfaces. Key features include:
• 0 to 1.5 mT linear range
• Can detect magnets more than 150 mm away
• Simple I2C interface
• Programmable digital threshold output
• 2% of full-scale accuracy for 0 to 125°C
• Fast 10000 sample-per-second update rate
• Factory calibrated
• Programmable offset and gain compensation
• -40°C to +125°C operating range
• Ultraminiature 2.5 x 2.5 mm DFN6 package
- Part Number:
- SM223-10E
- Quantity in Stock:
- 11
$6.88
IL860-1E: 5-Channel (all same direction) Top-of-the-Line Isolator, 2.5 kV, QSOP
The IL860-1E is NVE's top-of-the-line five-channel isolator, with best-in-class specifications:
• 110 Mbps
• 10 ns propagation delay
• DC-correct; deterministic power-up
• 50 kV/µs typ.; 30 kV/µs min. transient immunity
• 125 °C max. operating temperature
• 44000-year barrier life
• Low EMC footprint
The part uses NVE's 16-pin QSOP package.
The "E" suffix indicates this part is lead (Pb) free.
- Part Number:
- IL860-1E
- Quantity in Stock:
- 493
$9.40
IL4822E: Isolated RS422 Transceiver w/3.3-5V DC-DC Convertor, 2.5 kV, Wide SOIC
The IL4822 is an isolated, full-duplex 40 Mbps 5-volt bus RS-422 / RS-485 transceiver with an integrated 3.3V-to-5V DC-DC convertor.
The transceiver runs up to 40 Mbps, has a 1/5 Unit Load.
The DC-DC convertor can output up to 50 mA and is fully regulated.
2500 VRMS isolation; 16.5 kV bus ESD protection; 16-pin wide-body SOIC package with True 8™ mm creepage.
- Part Number:
- IL4822E
- Quantity in Stock:
- 806
$9.32
ABL005-10E: 0.5 mm, 1-Bridge Analog Gear-Tooth Sensor, TDFN
NVE's ABL005-10E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.5 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.500 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL005-10E
- Quantity in Stock:
- 1604
$5.19
ABT600-00E: TMR 2.4 mm Pitch Gear Tooth Sensor, MSOP
ABT600-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT600-00E is optimized for 2.4 mm pitch gears, and can be used for pitches from 1.6 to 4.8 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
- Part Number:
- ABT600-00E
$5.71
ABT500-00E: TMR 2 mm Pitch Gear Tooth Sensor, MSOP
ABT500-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT500-00E is optimized for 2 mm pitch gears, and can be used for pitches from 1.3 to 4 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
- Part Number:
- ABT500-00E
$5.71
AG972-07E: ABT375 TMR Gear-Tooth Sensor Demo Kit
The AG972-07E Demonstration Board showcases rotational encoding to
a few thousandths of a degree with an ABT375-00E sensor and a 30-tooth gear.
The kit includes:
• A 3 x 5-inch (76 x 127 mm) PCB
• An ABT375-00E gear tooth sensor
• An eight-digit rotational display
• a 30-tooth. 0.5 module gear
• Part #12216 ceramic bias magnet
• Test points for analog outputs
• Powered by two AAA batteries (included)
- Part Number:
- AG972-07E
- Quantity in Stock:
- 1
$195.00
ABT375-00E: TMR 1.5 mm Pitch Gear Tooth Sensor, MSOP
ABT375-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT375-00E is optimized for 1.5 mm pitch gears, and can be used for pitches from 1 to 3 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
A demo board is also available.
- Part Number:
- ABT375-00E
$5.71
