These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC
convertor, bypass capacitors as recommended, as well as test pads, screw terminals, provisions for header pins. LEDs that show the DC-to-DC convertor is operating.
The boards follow best practices including 2s2p with thermal vias for optimal thermal
performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.
The ILDC1xV-15 Series are ultraminiature one-quarter watt DC-to-DC convertors that generate independent outputs with 2.5 kV isolation from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL712-3E two channel (one each direction) high-speed isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
The boards let you evaluate the world's best isolators.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT026-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
The ALT026 is a Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor
with extraordinary signal amplitude and wide linear range. The differential bridge
output is bipolar, meaning it is positive for a positive field and negative for
an opposite field polarity. The ALT025 has cross-axis sensitivity (across the pads).
Features:
Large signal (200 mV/V)
Wheatstone bridge magnetometer configuration
0 - 10 V power supply
20 kiloohm device resistance for low power
±20 mT (±200 Oe) linear range
High linearity output (
These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC
convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating.
The boards follow best practices including 2s2p with thermal vias for optimal thermal
performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.
The ILDC1xV-15 Series are ultraminiature one-quarter watt DC-to-DC convertors that generate independent outputs with 2.5 kV isolation from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
NVE's ADL922-14E Ultraminiature Nanopower Switch integrates GMR sensor elements with onboard digital signal processing. Continuous operation allows high frequency switching. External duty cycling allows nanopower operation. The part is packaged in a 1.1 x 1.1 x 0.35 mm DFN4 package.
Features:
Precise 4 mT operate point
Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm DFN4 package
2.4 to 4.2 V
Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling
100 kHz Operating Frequency
Digital Switch Output
Applications:
Battery-Powered Devices
Wearables and IoT Sensors
Battery-Powered Devices
Industrial Sensors
These 2 x 3.5-inch (50 x 90 mm) boards have an IL715VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
This Evaluation Board provides a complete isolated three-channel SPI node, plus an isolated 3.3 V to 3.3 V DC-to-DC convertor using an IL7614VE. It is ideal for half-duplex SPI applications.
These 2 x 3.5-inch (50 x 90 mm) boards also include screw terminal and test pads, and uses a 2s2p board with vias for optimal thermal performance. LEDs indicate DC-to-DC convertor input and output power.
The IL7614V is a high-speed, fully-isolated, data couplers with an integrated, one-quarter watt 3.3 V-to-3.3 V DC-to-DC convertor. This level of integration dramatically reduces chip count and board area.
The ILDC13V-15E is a one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The "V" suffix indicates an extended creepage package and full 2.5 kV isolation.
The part can be used to power high-side gate supplies in H-bridges.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide virtually unlimited barrier life.
The ILDC12-15E is a one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The "V" suffix indicates an extended creepage package and full 2.5 kV isolation.
The part can be used to generate isolated RS-485 bus supplies or to power high-side gate supplies in H-bridges.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide virtually unlimited barrier life.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL717VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
These 2 x 3.5-inch (50 x 90 mm) boards have an IL716VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.