This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller.
The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration.
A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included.
The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.
The AAL024-10E high-performance magnetometer has high sensitivity, high linearity, low-hysteresis, and cross-axis sensitivity, making it ideal for noncontact current-sensing.
Features:
3.6 mv/V/Oe typical sensitivity for large output signals and low noise
Wide linear range: 0.15 – 1.05 mT; 1.5 mT saturation
2.2 kΩ bridge resistance/1.1 kΩ output impedance for easy interface
Low offset: 4 mV/V max.
Low hysteresis: 2% max. for excellent repeatability
Wide bandwidth: 100 kHz
63 V minimum inherent isolation (pad to electrical connections)
Ultraminiature 2.5 mm x 2.5 mm TDFN6 package
Applications:
Current sensing
Low-field sensing for magnetic media
Earths magnetic field detection
Low-Hysteresis Magnetometer
senses fields from permanent magnets, earth, and current sources.
Typ. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
15
1.5 - 10.5
3.0 - 4.2
2200 ±20%
TDFN6
(RoHS)
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
The AG919-06 is a 2 x 0.25 inch (50 x 6 mm) PCB designed to be used with MSOP8 sensors (-00E package; order sensors separately). The MSOP8 is rotated 90 degrees compared to the AG918-06.
The AA007-00E GMR Magnetic Field Sensors are used to sense relatively high fields.
0.1 mV/V/Oe Sensitivity; 500 Oe Saturation Field; MSOP8.
Note: Parts must be purchased in tube quantities (multiples
of 100) when purchasing quantities of 100 or more. Larger quantities are subject
to NVE's standard lead times.
A 1.2 x 0.25 inch x 0.031 inch thick (30 x 6 x 0.75 mm) PCB for demonstrating 1.1 x 1.1 mm DFN4/ULLGA sensors (-14E sensor suffix; order sensors separately).
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
A 1.57 x 0.25 inch PCB for demonstrating 1.1 x 1.1 mm DFN4/ULLGA sensors such as AHLxxx-14E, ADLxxx-14E, and ALT0xx-14E, (order sensors separately). In addition to space for the sensor, the boards have locations for 0402-size pull-up resistors and bypass capacitors.
Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.
The AAK001-14E is a high-field magnetometer sensor that provides precise sensing
of magnetic fields up to 4 kOe (400 mT). With a unique 1.1 mm x 1.1 mm package
package, it is also our smallest analog sensor.
Features:
Precise sensing of magnetic fields up to 4 kOe (400 mT)
Sensitive to fields of any direction in the IC plane
Ratiometric Wheatstone bridge outputs
Any operating supply voltage up to 12V
Ultraminiature 1.1 x 1.1 mm package
Applications:
Brushless DC motors
Motor commutator sensors
Noncontact high-current measurement
Harsh industrial applications
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
The AFL006-10E is the world's most sensitive magnetic switch. The switch is designed for use in low power
and battery applications. It can operate from a single cell with supplies as low as 0.9 V and typical supply current of 55 microamps.
Like all NVE magnetic
sensors, the AFL006-10E has extremely precise magnetic operate and release points.
Features:
4 Oe typical operate point for ultrahigh sensitivity
0.9 V – 2 V operating voltage for single-cell battery operation
Less than 100 microwatts power consumption
2.5 mm x 2.5 mm x 0.8 mm TDFN6 for miniaturization
Applications include:
Portable instruments
Utility meters
Noncontact overcurrent protection
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
AAT101-10E Angle Sensors use a Tunneling Magnetoresistance (TMR)
full-bridges to produce a very high output signal without amplification. The sensors also have a wide
airgap tolerance and high device resistance for low power. Sine
and cosine outputs provide full quadrature.
Key specifications are as follows:
Full-Bridge TMR Angle Sensor
Typ. p-p
Signal
Configuration
Min. Applied
Field
Nonsinusoidality
accuracy
Max. Op.
Temp.
Typ. Device
Resistance
Package
400 mV/V
Full bridge
30 Oe
1.5%
125°C
625 kΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
The AAL004-10E high-performance magnetometer has high sensitivity and low-hysteresis, making it ideal for low-field applications. With a unique TDFN6 package, it is also our smallest analog sensor.
Features:
Output linear with magnetic fields as low as 1.5 Oe for low-field applications
3.5 mv/V/Oe typical sensitivity for large output signals and low noise
2% maximum hysteresis for precision and repeatability
Omnipolar output for configuration flexibility
–40 to 125°C
Applications:
Current sensing
Low-field sensing for magnetic media
Earths magnetic field detection
Low-Hysteresis Magnetometer
senses fields from permanent magnets, earth, and current sources.
Typ. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
15
1.5 - 10.5
3.0 - 4.2
2200 ±20%
TDFN6
(RoHS)
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
The IL3685-1 is the industry's fastest isolated RS-485 transceiver (40 Mbps) in the industry's smallest package (QSOP16). 3.3 V or 5 V input logic; fully PROFIBUS compliant; 15 kV bus ESD protection; 50 kV per microsecond transient immunity.
This part is lead (Pb) free.
The IL3022E is a cost-effective isolated 4 Mbps RS-422 full-duplex transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
AAT006-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology for operation at magnetic fields as low as 15 Oe, allowing an extremely wide airgap tolerance. The device has a large output without amplification, and high device resistance for low power. Sine and cosine outputs provide full quadrature.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op. Temp.
Typ. Device
Resistance
Package
200 mV/V
15 Oe
0.5 degrees
125°C
1.25 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).