New Products

Displaying 381 to 390 (of 390 products)
IL7817VE: 4-channel (3 transmit, 1 receive) Isolator w/3.3-5V DC-DC Convertor

The IL7817VE is a four-channel (3 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7817VE

$12.40

IL7816VE: 4-channel (2 each direction) Isolator w/3.3-5V DC-DC Convertor

The IL7816VE is a four-channel (two each direction) 110 Mbps isolator with an integrated 3.3V-to-5V isolated DC-DC boost convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

4 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7616VE
Quantity in Stock:
776

$12.40

AG957-06E: Bare breakout board for ASR0xx Smart Angle Sensors

The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG957-06E
Quantity in Stock:
16

$2.25

ADT005-10E: High Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6

ADT005-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.

The ADT005 is higher hysteresis than the ADT002 for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.

To minimize power, the ADT005 does not include the high-field detection circuitry included in the ADT001 version, and is slightly less accurate due to lower-power circuitry.

The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.

The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.

Part Number:
ADT005-10E

$10.61

ALT021-10E: 0-0.25 mT TMR Bipolar Analog Sensor, 20 KOhm, x-axis, TDFN6

The ALT021 is an ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. Features: ±0.25 mT linear range Ultrahigh sensitivity (500 mV/V/mT typical) Large output signal (200 mV/V/mT typical) 0 - 10 V power supply Wheatstone bridge magnetometer configuration 20 kiloohm device resistance for low power Up to 300 kHz frequency bandwidth 2.5 x 2.5 mm TDFN6 package –40 to 125°C Applications: Motion, speed, and position control
Non-contact current sensing
Mechatronics and robotics
Navigation

Part Number:
ALT021-10E

$12.00

ILDC12-01: Ultraminiature Isolated 3.3-to-5V DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-5 V version of world’s smallest isolated DC-to-DC convertor, the ILDC12-15E.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC12 is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC12-01

$49.95

ILDC13-01: Ultraminiature Isolated 3.3-to-6V DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-6 V version of the world’s smallest isolated DC-to-DC convertor, the ILDC13-15E.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC13-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC13-15E is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated six-volt gate supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC13-01

$49.95

ILDC11V-01: Miniature Isolated 3.3-to-3.3V DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-3.3V version of our miniature DC-DC convertor, the ILDC11VE.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC11-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC11VE is a miniature one-quarter watt DC-to-DC convertor with 4 kV isolation that can generate an isolated 3.3-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC11V-01

$49.95

ILDC12V-01: Miniature Isolated 3.3-to-5V DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-5 V version of our miniature DC-to-DC convertor, the ILDC12VE.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12VE plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC12 is an ultraminiature one-quarter watt DC-to-DC boost convertor with 4 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC12V-01

$49.95

ILDC13V-01: Miniature Isolated 3.3-to-6V DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-6 V version of our miniature DC-to-DC convertor, the ILDC13VE.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC13VE plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC13VE is an miniature one-quarter watt DC-to-DC boost convertor with 4 kV isolation that can be used to generate an isolated six-volt gate supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC13V-01

$49.95

Displaying 381 to 390 (of 390 products)