New Products
IL41050TTE: Basic Isolated CAN Transceiver, 2.5 kV, Wide SOIC
The IL41050TT is a low-cost, basic CAN transceiver without Vref output and silent mode input pins. 2.5kV isolation; 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic. 16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
- Part Number:
- IL41050TTE
- Quantity in Stock:
- 410
$3.62
IL41050TTVE: Basic Isolated CAN Transceiver, 5 kV, Wide SOIC
The IL41050TTVE is a low-cost, 5 kV basic CAN transceiver without Vref output and silent mode input pins. 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic. 16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
- Part Number:
- IL41050TTVE
- Quantity in Stock:
- 89134
$4.19
AG915-06: MSOP8 Printed Circuit Board (0.25" octagonal)
A 0.25-inch (6 mm) octagonal PCB for easy connections to MSOP8 sensors (-00E suffix; order sensors separately).
The PCB provides through holes for #28 or #30 wires.
- Part Number:
- AG915-06
- Quantity in Stock:
- 822
$2.25
AG932-07E: ADT002 Rotation Sensor Evaluation Kit
The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.
- Part Number:
- AG932-07E
- Quantity in Stock:
- 11
$90.00
ADT001-10E: High Hysteresis, Rotation Quadrant Sensor w/high-field detection, TDFN6
ADT001-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information. An additional output indicates a fault if the magnetic field is too high. The ADT001 is high hysteresis for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction. The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size. The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
- Part Number:
- ADT001-10E
- Quantity in Stock:
- 12976
$11.18
AAT009-10E: Angle Sensor, 6 MOhm, TDFN6
AAT009-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology for ultralow power, high output signal, and a wide airgap tolerance. Sine and cosine outputs provide
full quadrature. The AAT009-10E version has the highest device resistance in the AAT product family (6 megaohms typ.), for the lowest power consumption.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op.
Temp.
Typ. Device
Resistance
Package
200 mV/V
30 Oe
0.5 degrees
125°C
6 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
- Part Number:
- AAT009-10E
- Quantity in Stock:
- 4869
$8.94
AG931-07E: AAT003 40 KOhm Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
- Part Number:
- AG931-07E
- Quantity in Stock:
- 22
$75.00
ADT002-10E: Low Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6
ADT002-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information. The ADT002 is lower hysteresis than the ADT005 to provide accurate, absolute rotational quadrant information. The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size. The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
- Part Number:
- ADT002-10E
- Quantity in Stock:
- 15099
$11.18
AG941-07E: ADL-Series Sensor Demo Board
The kit includes a demo board with three ultraminiature, ultralow-power ADL-Series magnetic sensors. Each sensor drives an indicator LED, and a meter shows the sensor power in microamps or nanoamps. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by a coin cell (included).
- Part Number:
- AG941-07E
- Quantity in Stock:
- 3
$90.00
AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040B
- Quantity in Stock:
- 31
$19.95
AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
- Part Number:
- AG040C
- Quantity in Stock:
- 27
$16.95
AAT006-10E: Low-Field Angle Sensor, TDFN6
AAT006-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology for operation at magnetic fields as low as 15 Oe, allowing an extremely wide airgap tolerance. The device has a large output without amplification, and high device resistance for low power. Sine and cosine outputs provide full quadrature.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op.
Temp.
Typ. Device
Resistance
Package
200 mV/V
15 Oe
0.5 degrees
125°C
1.25 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
- Part Number:
- AAT006-10E
- Quantity in Stock:
- 35000
$8.94
IL3022E: Low-Cost Isolated RS422 Transceiver, 2.5 kV, Wide SOIC
The IL3022E is a cost-effective isolated 4 Mbps RS-422 full-duplex transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
- Part Number:
- IL3022E
- Quantity in Stock:
- 12897
$5.05
IL3685-1E: 40 Mbps Isolated RS485 Transceiver, 2.5 kV, QSOP
The IL3685-1 is the industry's fastest isolated RS-485 transceiver (40 Mbps) in the industry's smallest package (QSOP16). 3.3 V or 5 V input logic; fully PROFIBUS compliant; 15 kV bus ESD protection; 50 kV per microsecond transient immunity.
This part is lead (Pb) free.
Lead-free
product information
- Part Number:
- IL3685-1E
- Quantity in Stock:
- 3600
$6.89
AAL004-10E: 1.5 mT Sat. Analog Sensor, 2.2 KOhm, TDFN6
The AAL004-10E high-performance magnetometer has high sensitivity and low-hysteresis, making it ideal for low-field applications. With a unique TDFN6 package, it is also our smallest analog sensor.
Features:
Output linear with magnetic fields as low as 1.5 Oe for low-field applications
3.5 mv/V/Oe typical sensitivity for large output signals and low noise
2% maximum hysteresis for precision and repeatability
Omnipolar output for configuration flexibility
–40 to 125°C
Applications:
Current sensing
Low-field sensing for magnetic media
Earth’s magnetic field detection
Low-Hysteresis Magnetometer—
senses fields from permanent magnets, earth, and current sources.
Typ. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
15
1.5 - 10.5
3.0 - 4.2
2200 ±20%
TDFN6
(RoHS)
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
- Part Number:
- AAL004-10E
- Quantity in Stock:
- 17523
$9.60
AAT101-10E: Full-Bridge Angle Sensor, 625 kOhm, TDFN6
AAT101-10E Angle Sensors use a Tunneling Magnetoresistance (TMR)
full-bridges to produce a very high output signal without amplification. The sensors also have a wide
airgap tolerance and high device resistance for low power. Sine
and cosine outputs provide full quadrature.
Key specifications are as follows:
Full-Bridge TMR Angle Sensor
Typ. p-p
Signal
Configuration
Min. Applied
Field
Nonsinusoidality
accuracy
Max. Op.
Temp.
Typ. Device
Resistance
Package
400 mV/V
Full bridge
30 Oe
1.5%
125°C
625 kΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
- Part Number:
- AAT101-10E
- Quantity in Stock:
- 19880
$8.94
AFL006-10E: 0.4 mT Digital Sw, 0.9 V – 2 V, Norm OFF Sinking, TDFN
The AFL006-10E is the world's most sensitive magnetic switch. The switch is designed for use in low power and battery applications. It can operate from a single cell with supplies as low as 0.9 V and typical supply current of 55 microamps. Like all NVE magnetic sensors, the AFL006-10E has extremely precise magnetic operate and release points. Features: 4 Oe typical operate point for ultrahigh sensitivity 0.9 V – 2 V operating voltage for single-cell battery operation Less than 100 microwatts power consumption 2.5 mm x 2.5 mm x 0.8 mm TDFN6 for miniaturization Applications include: Portable instruments Utility meters Noncontact overcurrent protection Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times. This part is RoHS compliant.
- Part Number:
- AFL006-10E
- Quantity in Stock:
- 434
$9.25
AAK001-14E: 400 mT Sat. High-Field Magnetometer, 3.5 KOhm, ULLGA
The AAK001-14E is a high-field magnetometer sensor that provides precise sensing
of magnetic fields up to 4 kOe (400 mT). With a unique 1.1 mm x 1.1 mm package
package, it is also our smallest analog sensor.
Features:
Precise sensing of magnetic fields up to 4 kOe (400 mT)
Sensitive to fields of any direction in the IC plane
Ratiometric Wheatstone bridge outputs
Any operating supply voltage up to 12V
Ultraminiature 1.1 x 1.1 mm package
Applications:
Brushless DC motors
Motor commutator sensors
Noncontact high-current measurement
Harsh industrial applications
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
- Part Number:
- AAK001-14E
- Quantity in Stock:
- 36
$17.05
AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.
- Part Number:
- AG934-07E
- Quantity in Stock:
- 1
$75.00
AG910-07E: GMR Switch Evaluation Kit w/ZIF socket
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
- Part Number:
- AG910-07E
- Quantity in Stock:
- 10
$90.00
