Features include 3.3 V or 5.0 V input logic, 15 kV bus ESD protection, 5 Mbps data rate, and 20 kV per microsecond transient immunity. 16-pin narrow-body (0.15'') SOIC package.
This part is lead (Pb) free.
Lead-free
product information
The Il715-3 is a 3.3/5V, multichannel isolated 110 Mbps CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin narrow-body (0.15"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
ADT001-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.
An additional output indicates a fault if the magnetic field is too high.
The ADT001 is high hysteresis for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction.
The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.
The sensors are typically used with
radially-magnetized disk magnets or split pole magnet.
An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
NVE's AHL925-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing. The Nanopower Switch is extremely small and low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package
Low Voltage Operation to 0.9 V
35 Microamps Typical Supply Current
Digital Switch Output
Applications:
Battery-Powered Devices
Portable Instruments
AAT101-10E Angle Sensors use a Tunneling Magnetoresistance (TMR)
full-bridges to produce a very high output signal without amplification. The sensors also have a wide
airgap tolerance and high device resistance for low power. Sine
and cosine outputs provide full quadrature.
Key specifications are as follows:
Full-Bridge TMR Angle Sensor
Typ. p-p
Signal
Configuration
Min. Applied
Field
Nonsinusoidality
accuracy
Max. Op.
Temp.
Typ. Device
Resistance
Package
400 mV/V
Full bridge
30 Oe
1.5%
125°C
625 kΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
NVE's ABL004-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 1.0 mm apart on the sensor IC arranged in a full bridge configuration.
Bridge Resistance (Ohms)
Linear Range (Oersteds)
Output
Comments
Package
Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm.
4K - 7K
+/-5 to +/-100
Analog Bridge
Gear Tooth or Encoder
TDFN6
Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
The IL715-1 is an ultraminiature isolator with no performance compromises. 110 Mbps, 10 ns propagation delay, 3 ns pulse width distortion, 600 WV per VDE 0884-10, 2500 Vrms isolation and 50 kV/microsecond transient immunity, and 44000 year barrier life. 16-pin QSOP.
The "E" suffix indicates this part is lead (Pb) free.
The AAL004-10E high-performance magnetometer has high sensitivity and low-hysteresis, making it ideal for low-field applications. With a unique TDFN6 package, it is also our smallest analog sensor.
Features:
Output linear with magnetic fields as low as 1.5 Oe for low-field applications
3.5 mv/V/Oe typical sensitivity for large output signals and low noise
2% maximum hysteresis for precision and repeatability
Omnipolar output for configuration flexibility
–40 to 125°C
Applications:
Current sensing
Low-field sensing for magnetic media
Earths magnetic field detection
Low-Hysteresis Magnetometer
senses fields from permanent magnets, earth, and current sources.
Typ. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
15
1.5 - 10.5
3.0 - 4.2
2200 ±20%
TDFN6
(RoHS)
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
The IL716 is a 3.3-volt, multichannel isolated 110 Mbps CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 50 kV/microsecond transient immunity. 16-pin wide-body (0.3"-wide) SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL3085E is a cost-effective isolated 4 Mbps RS-485 transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
NVE's ADL924-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package
2.4 to 4.2 V
Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling
250 kHz Operating Frequency
Digital Switch Output
Applications:
Battery-Powered Devices
Portable Instruments
The IL511-3 is a 3.3V/5V, dual-channel unidirectional 2 Mbps DC-correct digital isolator, 25 ns propagation delay, 10 ns pulse width distortion with 2500 Vrms isolation and 50 kV/microsecond typical transient immunity, -40°C to 85°C. 8-pin SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
The IL521-3 is a 3.3V/5V, dual-channel bidirectional 2 Mbps DC-correct digital isolator, 25 ns propagation delay, 10 ns pulse width distortion with 2500 Vrms isolation and 50 kV/microsecond typical transient immunity, -40°C to 85°C. 8-pin SOIC package.
The "E" suffix indicates this part is lead (Pb) free.
ADT002-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information.
The ADT002 is lower hysteresis than the ADT005 to provide accurate, absolute rotational quadrant information.
The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size.
The sensors are typically used with
radially-magnetized disk magnets or split pole magnet.
An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
AAT006-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology for operation at magnetic fields as low as 15 Oe, allowing an extremely wide airgap tolerance. The device has a large output without amplification, and high device resistance for low power. Sine and cosine outputs provide full quadrature.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op. Temp.
Typ. Device
Resistance
Package
200 mV/V
15 Oe
0.5 degrees
125°C
1.25 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
The IL3022E is a cost-effective isolated 4 Mbps RS-422 full-duplex transceiver, compatible with 3.3 V or 5 V input logic. 7 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage.
The IL41050TAE is a high-speed, low-power isolated ISO 11898 compliant CAN transceiver. 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic.
16-pin wide-body (0.3'') RoHS SOIC package with full 8 mm creepage.
NVE's ADL121-14E Nanopower Switch integrates GMR sensor elements with digital onboard
signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power.
Features:
Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package
2.4 to 4.2 V
Typical Power Consumption 72 nW at 2.4 V
30 Hz Typical Update Frequency
Digital Switch Output
Integrated Duty-Cycling
Applications:
Battery-Powered Devices
Portable Instruments
The IL261-1E is an ultraminiature isolator with no performance compromises. 110 Mbps, 10 ns propagation delay, 3 ns pulse width distortion, 600 WV per VDE 0884-10, 2500 Vrms isolation and 50 kV/microsecond transient immunity, and 44000 year barrier life. 16-pin QSOP.
The "E" suffix indicates this part is lead (Pb) free.