AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant.
A 3-volt coin cell (included) powers the board.
The AG957-06E provides easy connections to an ASR-Series Smart Angle Sensor (sensors sold separately). In addition a spot for the sensor, the board has a spot for a bypass capacitor and a header to connected to the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The isolated CAN FD Evaluation Board provides a complete isolated Controller Area Network node using the world's smallest isolated CAN FD transceiver, the IL41050TFD-1E.
The board is fully ISO 11898 CAN compliant and accommodates 3V - 5.5V supplies. It provides screw terminal connections, termination resistors, pull-up resistors, and a jumper to select normal or silent mode.
AET100F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The IL711V-1 is a dual-channel bidirectional, 110 Mbaud CMOS-compatible isolated buffer with full 2.5 kVrms isolation voltage in a unique 8-pin MSOP package. 10 ns propagation delay, 3 ns pulse width distortion, and 50 kV/microsecond transient immunity.
The "E" suffix indicates this part is lead (Pb) free.
The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
The AG951-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable SM324-10E Smart TMR Magnetometer. The kit includes:
An evaluation board with:
- an SM324-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A powerful, intuitive graphical user interface.
Simple software installation.
Flexibility to power from USB or an external power supply.
Isolated USB interface for safety and noise minimization.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle.
The kit also includes a split-pole magnet and a plastic magnet locating fixture.
The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
The AAK001-14E is a high-field magnetometer sensor that provides precise sensing
of magnetic fields up to 4 kOe (400 mT). With a unique 1.1 mm x 1.1 mm package
package, it is also our smallest analog sensor.
Features:
Precise sensing of magnetic fields up to 4 kOe (400 mT)
Sensitive to fields of any direction in the IC plane
Ratiometric Wheatstone bridge outputs
Any operating supply voltage up to 12V
Ultraminiature 1.1 x 1.1 mm package
Applications:
Brushless DC motors
Motor commutator sensors
Noncontact high-current measurement
Harsh industrial applications
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.