New Products

Displaying 41 to 60 (of 364 products)
IL721VE: 6 kV, 125C, 2-Channel (1 each direction) Isolator, Wide SOIC

The IL721VE is a 6 kVrms isolation, 125C, 3.3/5V, two channel, isolated, 110 Mbps, CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, and 50 kV/microsecond transient immunity. 16-pin wide-body SOIC package with True 8™ mm creepage. The "E" suffix indicates this part is lead (Pb) free.

Part Number:
IL721VE

$7.26

IL7612VE: Two-channel (one each direction) Isolator w/DC-DC Convertor

The IL7612VE is a two-channel (one each direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

5 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7612VE

$11.16

IL7614VE: 3-channel (both same direction) Isolator w/DC-DC Convertor

The IL7614VE is a three-channel (2 transmit, 1 receive) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

5 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7614VE

$11.78

IL7615VE: 4-channel (all same direction) Isolator w/DC-DC Convertor

The IL7615VE is a four-channel (all the same direction) 110 Mbps isolator with an integrated 3.3V-to-3.3V isolated DC-DC convertor.

The DC-DC convertor can output up to 250 mW, is fully regulated, and has built-in EMI mitigation.

5 kVRMS isolation; 125 C; 16-pin wide-body SOIC package with True 8™ mm creepage.

Part Number:
IL7615VE

$12.40

SM124-10E: General-Purpose 1 mT Smart GMR Magnetometer, TDFN6

The SM124-10E Smart Magnetometer combines an omnipolar GMR sensor element with with easy-to-use digital signal processing.

A digital output provides precise, programmable thresholds. An I²C interface provides magnetic field data, as well as a calibration interface. The device is factory calibrated for accuracy. Calibration coefficients are stored in internal nonvolatile memory.

All commands, data, and coefficients are a single byte, and a slick, elegant data structure lets you get up and running with a minimum of firmware.

Key features include:
  • Can detect magnets more than 50 mm away
  • I²C and digital threshold outputs
  • 0-1 mT linear range
  • 8-bit / 1% output resolution
  • −40°C to +125°C operating range
  • 5% FS accuracy for 0 to 85°C
  • 10 kSps sample rate for fast response
  • 6 mA typical supply current
  • In-plane sensitivity more usable than Hall effect sensors
  • Programmable offset and gain compensation
  • Optional magnet temperature compensation   • 2.2 to 3.6 volt supply
  • Ultraminiature 2.5 x 2.5 x 0.8 mm TDFN package

Part Number:
SM124-10E

$4.13

12592: 5 mm pitch magnetic linear scale tape, 1 x 20 cm

This magnetic scale tape is designed to be used with AET500-00E 5 mm pitch linear sensor. 1 cm (0.4 inches) wide by 20 cm (8 inches) long.

Part Number:
12592
Quantity in Stock:
1

$30.00

AD924-00E: 2.8 mT Digital Switch, RoHS MSOP

AD924-00E Sensors are for use with external high-current output transistors in industrial control environments. The parts provide the same precise magnetic performance as NVE's GMR Digital Switches with the addition of output stage short circuit protection (SCP). The protection circuit shuts off the output stage if there is a short circuit, then turns it back on after a specified interval. The sensor, combined with external reverse battery and overvoltage protection, results in a "bulletproof" assembly. Features: Precision Magnetic Operate Point -- 28 Gauss Excellent Temperature and Voltage Performance Digital Outputs Frequency Response 0 to 250 KHz Small, Low Profile Surface Mount Packages Applications: General Digital Field Sensing Pneumatic Cylinder Position Sensing Speed Sensing Supply
Voltage
min.-max. Supply
Current
(mA)
min.-max. Op. Point
(Oe)
min.-max. Differ-
ential
(Oe)
min. Output
Sat.
Voltage
max. Output Pkg. Mark Orien-
tation Pkg. 4.5-30.0 2.5-4.5 21-34 5 0.4 Sink/
Source/
Vreg/
SCP NBF Cross axis MSOP8
(RoHS) Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
AD924-00E
Quantity in Stock:
1

$5.65

DB001-00E: Signal Processing IC MSOP

NVE's DB001-00E signal processing IC is designed to work with NVE's AD9xx series GMR switch with short circuit protection. This combination provides a high-current switched output that corresponds to the sensor input. The DB001-00E functions as the front end of a complete sensor assembly, and includes protection against short circuits and high voltage transients from capacitive and inductive loads. The parts also feature thermal shutdown circuitry and reverse battery protection. They provide a regulated output voltage for the sensor and other components in the assembly, and an LED driver to indicate an "ON" condition. Features: High Current Output Reverse Battery and Transient Protection LED Driver Excellent Temperature and Voltage Performance Small, Low Profile Surface Mount Packages Note: Parts must be purchased in multiples of 100 when purchased in quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
DB001-00E
Quantity in Stock:
1

$3.95

IL717T: 125C 4-Channel (3 transmit, 1 receive) Isolator, 2.5 kV, Wide SOIC (Pb)

The IL717T is a high temperature, 3.3/5V, multi-channel, isolated, 110 Mbps, CMOS-compatible logic buffer with automatic level shifting, 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 20 kV/microsecond transient immunity. 16-pin wide-body (0.3"-wide) SOIC package.

Part Number:
IL717T
Quantity in Stock:
1

$8.23

AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board

The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040T
Quantity in Stock:
2

$19.95

AG959-07E: SM225 High-Speed Smart TMR Magnetometer breakout board

The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG959-07E
Quantity in Stock:
2

$19.95

AG966-07E: ASR012 I2C/PWM Smart TMR Angle Sensor breakout board

The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG966-07E
Quantity in Stock:
2

$19.95

AG969-07E: SM228-10E Smart I²C TMR Magnetometer Evaluation Kit

The AG969-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM228-10E sensor.
          - a microcontroller connected to the sensor via I2C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • An LED indicating the state of the threshold output.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG969-07E
Quantity in Stock:
2

$95.00

IL3685-3E: PROFIBUS-Compatible Isolated RS485 Transceiver, 2.5 kV, Narrow SOIC

The IL3685-3 is an isolated 40 Mbps RS-485 transceiver that is fully PROFIBUS compliant. 3.3 V or 5 V input logic. 15 kV bus ESD protection; 50 kV per microsecond transient immunity. 16-pin narrow-body (0.15''-wide) SOIC package This part is lead (Pb) free.

Lead-free product information

Part Number:
IL3685-3E
Quantity in Stock:
2

$5.28

12545: Holder for 8 mm dia. disk magnet

A machined-aluminum magnet holder for 8 mm dia. magnets such as part numbers 12527 and 12528 (sold separately).

Compatible with AG93x-Series and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.

Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.

Part Number:
12545
Quantity in Stock:
3

$70.00

12546: Holder for 4 mm dia. disk magnet

A machined-aluminum magnet holder for 4 mm dia. magnets such as part number 12526 (sold separately).

Compatible with AG93x-Series and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.

Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.

Part Number:
12546
Quantity in Stock:
3

$70.00

AG921-07E: AKL001 Gear-Tooth Sensor Demonstrator

A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".

Part Number:
AG921-07E
Quantity in Stock:
3

$90.00

AG932-07E: ADT002 Rotation Sensor Evaluation Kit

The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.

Part Number:
AG932-07E
Quantity in Stock:
3

$90.00

AG954-07E: TDFN6 Socket Board

The AG954-07E provides a socket for easy programming and prototyping of TDFN6 devices without soldering and unsoldering.

The custom socket is compatible with NVE's 2.5 mm x 2.5 mm TDFN6 package parts (-10E suffixes).

The board is 1.5" x 2" (38 mm x 50 mm), and uses brass hardware to minimize magnetic interference with the socketed sensor.
A 0.1"-spaced header provides for connections to the sensors, and a row of 0.1"-spaced through-holes allows for auxiliary parts such as a decoupling capacitor or an LED.

Part Number:
AG954-07E
Quantity in Stock:
3

$129.00

AG958-07E: SM124 Smart GMR Magnetometer breakout board w/connector

The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG958-07E
Quantity in Stock:
3

$24.95

Displaying 41 to 60 (of 364 products)