The IL41050TA-1E is an ultaminiature isolated CAN transceiver with no performance compromises. High-speed; low-power; 125C; 180 ns typ. loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic. 16-pin QSOP package--the world's smallest isolated transceiver.
$3.61
The AA007-00E GMR Magnetic Field Sensors are used to sense relatively high fields.
0.1 mV/V/Oe Sensitivity; 500 Oe Saturation Field; MSOP8.
Note: Parts must be purchased in tube quantities (multiples
of 100) when purchasing quantities of 100 or more. Larger quantities are subject
to NVE's standard lead times.
$10.90
The AAK001-14E is a high-field magnetometer sensor that provides precise sensing
of magnetic fields up to 4 kOe (400 mT). With a unique 1.1 mm x 1.1 mm package
package, it is also our smallest analog sensor.
Features:
Precise sensing of magnetic fields up to 4 kOe (400 mT)
Sensitive to fields of any direction in the IC plane
Ratiometric Wheatstone bridge outputs
Any operating supply voltage up to 12V
Ultraminiature 1.1 x 1.1 mm package
Applications:
Brushless DC motors
Motor commutator sensors
Noncontact high-current measurement
Harsh industrial applications
Note: Parts are sold in increments of 100 for quantities of 100 or more.
This part is RoHS compliant.
$11.52
AAT006-10E Angle Sensors use Tunneling Magnetoresistance (TMR) technology for operation at magnetic fields as low as 15 Oe, allowing an extremely wide airgap tolerance. The device has a large output without amplification, and high device resistance for low power. Sine and cosine outputs provide full quadrature.
Key specifications are as follows:
TMR Angle Sensor
Typ. p-p
Signal
Min. Applied
Field (Oe)
Max. Angular
Error (const. field)
Max. Op.
Temp.
Typ. Device
Resistance
Package
200 mV/V
15 Oe
0.5 degrees
125°C
1.25 MΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
$5.50
AD924-00 Sensors are for use with external high-current output transistors in
industrial control environments. The parts provide the same precise magnetic performance
as NVE's GMR Digital Switches with the addition of output stage short circuit
protection (SCP). The protection circuit shuts off the output stage if there is
a short circuit, then turns it back on after a specified interval. The sensor,
combined with external reverse battery and overvoltage protection, results in
a "bulletproof" assembly.
Features:
Precision Magnetic Operate Point -- 28 Gauss
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Sink/
Source/
Vreg/
SCP
NBF
Cross axis
MSOP8
(Pb)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
$5.65
AD924-00E Sensors are for use with external high-current output transistors in
industrial control environments. The parts provide the same precise magnetic performance
as NVE's GMR Digital Switches with the addition of output stage short circuit
protection (SCP). The protection circuit shuts off the output stage if there is
a short circuit, then turns it back on after a specified interval. The sensor,
combined with external reverse battery and overvoltage protection, results in
a "bulletproof" assembly.
Features:
Precision Magnetic Operate Point -- 28 Gauss
Excellent Temperature and Voltage Performance
Digital Outputs
Frequency Response 0 to 250 KHz
Small, Low Profile Surface Mount Packages
Applications:
General Digital Field Sensing
Pneumatic Cylinder Position Sensing
Speed Sensing
Supply
Voltage
min.-max.
Supply
Current
(mA)
min.-max.
Op. Point
(Oe)
min.-max.
Differ-
ential
(Oe)
min.
Output
Sat.
Voltage
max.
Output
Pkg. Mark
Orien-
tation
Pkg.
4.5-30.0
2.5-4.5
21-34
5
0.4
Sink/
Source/
Vreg/
SCP
NBF
Cross axis
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
$5.65
ADT001-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information. An additional output indicates a fault if the magnetic field is too high. The ADT001 is high hysteresis for high noise immunity in applications such as speed sensing and counting rotations or where motion is in only one direction. The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size. The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
$7.15
ADT002-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information. An additional output indicates a fault if the magnetic field is too high. The ADT002 is low hysteresis to provide accurate, absolute rotational quadrant information. The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size. The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
$7.15
AET100F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.
The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.
Evaluation and Demonstration
Kits are also available.
$6.88
This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
$16.95
This self-contained module allows zeroing and programming the digital output threshold and hysteresis or SM124-10E or SM125-10E Smart Magnetometer without need of a computer or a customer microcontroller.
The 2.5" x 2.5" (64 mm x 64 mm) board has an I²C master microcontroller connected to the SM124.
A pushbutton for zeros the sensor, and miniature rotary thumbwheel switches provide three digits of resolution for the threshold and two for hysteresis. A custom TDFN-6 socket accommodates the 2.5 mm x 2.5 mm SM12x-10E. The module is powered by a small wall-mounted power supply (included).
Jumpers allow the sensor to be disconnected from the rest of the board so the board can be used as an interface to the customer’s electronics.
This module includes:
• A 2.5 x 2.5 mm TDFN6 socket for a SM12x-10E Smart Magnetometer
• A preprogrammed, onboard microcontroller
• Two sets of thumbwheel switches for digital threshold and hysteresis
• Two LEDs indicating the sensor’s output and successful programming
• A 5-volt wall-mount power supply
Sensors are sold separately.
$195.00
The AG956-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR002-10E Smart Angle Sensor. The kit includes:
• An evaluation board with:
- an ASR002-10E sensor
- a diametrical
magnet
- magnet fixturing and a
• An interface board with:
- a microcontroller
connected to the sensor via SPI
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
• A powerful, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a
computer.
$195.00
The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$24.95
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$24.95
NVE's AHL925-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing. The Nanopower Switch is extremely small and low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package Low Voltage Operation to 0.9 V 35 Microamps Typical Supply Current Digital Switch Output Applications: Battery-Powered Devices Portable Instruments
$7.60
AHT924-Series Nanopower Switches integrate TMR sensor elements with digital onboard signal processing. The ultralow power TMR element provides nanopower without duty cycling. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package Low Voltage Operation to 0.9 V 1 microamp Typical Supply Current Digital Switch Output Applications: Battery-Powered Devices Portable Instruments
$8.36
NVE's DB002-02 signal processing IC is designed to work with NVE's AD1xx series GMR switch as well as any other current sourcing or CMOS/TTL digital output sensor element, such as an inductive sensor or a photo sensor. This combination provides a high current switched output that corresponds to the sensor input. The DB002-02 functions as the front end of a complete sensor assembly, and includes protection against short circuits and high voltage transients from capacitive and inductive loads. The parts also feature thermal shutdown circuitry and reverse battery protection. It provides a regulated output voltage for the sensor and other components in the assembly, and an LED driver to indicate an "ON" condition. Features: High Current Output Reverse Battery and Transient Protection LED Driver Excellent Temperature and Voltage Performance Small, Low Profile Surface Mount Packages Note: Parts must be purchased in multiples of 92 for quantities of 92 or more. Larger quantities are subject to NVE's standard lead times.
$4.25
The IL261E is a 3.3/5.0-volt, 5-channel (4 transmit; 1 receive) isolated, 110 MBaud CMOS compatible logic buffers with 10 ns propagation delay, 3 ns pulse width distortion, 2500 Vrms isolation and 30 kV/microsecond transient immunity. 16-pin wide-body (0.3"-wide) SOIC package. The "E" suffix indicates this part is lead (Pb) free.
$8.54
This board implements a complete isolated 5-volt RS-485 node using an IL2985E low-power transceiver, an ILDC11-15E ultraminiature isolated DC-DC convertor, and a commodity boost regulator.
The
4 by 3 inch (100 by 75 mm) board provides screw terminal and test point connections.
The IL2985E is a low-power, fully-isolated, differential 5-volt bus transceiver. The ILDC11-15E isolates the 3.3-volt controller supply, and a boost regulator provides a fully-isolated five-volt bus supply.
$84.95
The IL41050TE is an isolated CAN transceiver. 125C; 210 ns loop delay; ISO 11898 compliant; >110 node fanout; 1 Mbps; 3.3 V or 5.0 V input logic. 16-pin wide-body (0.3''-wide) SOIC package. This is a LEGACY PART--the IL41050TAE is recommended for new designs.
$3.80
