NVE's AHL024-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package Low Voltage Operation to 0.9 V 95 nA Typical Supply Current 110 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycle Operation Applications: Battery-Powered Devices Portable Instruments
$7.60
NVE's AHL023-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package Low Voltage Operation to 0.9 V 95 nA Typical Supply Current 110 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycle Operation Applications: Battery-Powered Devices Portable Instruments
$7.60
NVE's AHL021-14E Nanopower Switch integrates GMR sensor elements with digital onboard signal processing and duty-cycling electronics. The Nanopower Switch is extremely small and extremely low power. Features: Ultraminiature 1.1 mm x 1.1 mm x 0.45 mm ULLGA package Low Voltage Operation to 0.9 V 95 nA Typical Supply Current 110 Hz Typical Update Frequency Digital Switch Output Integrated Duty-Cycle Operation Applications: Battery-Powered Devices Portable Instruments
$7.60
The unique AHK991-14E is a high-field, low voltage, low power, TMR magnetic switch.
The sensors have a 350 mT (3500 Oe) typical operate point, which is high enough to detect strong, rare-earth magnets in close proximity that disrupts lower-field sensors.
The sensors can withstand unlimited fields without
being damaged or turning off.
Unlike Hall effect or other sensors, the switch is sensitive to magnetic fields in any direction.
Key Specifications:
350 mT operate point
0.9 to 1.8 V
2 µA typical supply current
3000 Hz switching speed
-40 to 85°C
$8.36
The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.
Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.
$195.00
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
$19.95
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
$50.00
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00
The AG972-07E Demonstration Board showcases rotational encoding to
a few thousandths of a degree with an ABT375-00E sensor and a 30-tooth gear.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An ABT375-00E gear tooth sensor
An eight-digit rotational display
a 30-tooth. 0.5 module gear
Part #12216 ceramic bias magnet
Test points for analog outputs
Powered by two AAA batteries (included)
$195.00
The AG970-07E Evaluation Kit helps test a variety AET-Series sensors with linear magnetic scales. The kit includes:
All five AET-Series parts (unsoldered in tubes)
A 3 x 4-inch (76 x 101 mm) PCB with test points and screw terminals
Detachable fixturing for linear magnetic tape (tape sold separately)
$65.00
The AG969-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00
The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
$19.95
The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$19.95
The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
$195.00
The AG964-07E Demonstation Board has everything you need to evaluate
the remarkable ASR022-10E ABZ TMR Encoder Sensor. The demonstration includes:
ASR022-10E ABZ Noncontact TMR Encoder Sensor
A four-digit display to indicate rotation
Part # 12426 split-pole Alnico 5 round horseshoe magnet
LEDs for A, B, Z, and Direction outputs
Plastic magnet locating fixture
Powered by two AAA batteries (included)
$195.00
The AG963-07E Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR012-10E I2C Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR012-10E sensor
- a diametrical
magnet
- magnet fixturing
An interface board with:
- a microcontroller
connected to the sensor via I²C
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
$195.00
The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM125-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
$95.00
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
$24.95