New Products
AAT101-10E: Full-Bridge Angle Sensor, 625 kOhm, TDFN6
AAT101-10E Angle Sensors use a Tunneling Magnetoresistance (TMR)
full-bridges to produce a very high output signal without amplification. The sensors also have a wide
airgap tolerance and high device resistance for low power. Sine
and cosine outputs provide full quadrature.
Key specifications are as follows:
Full-Bridge TMR Angle Sensor
Typ. p-p
Signal
Configuration
Min. Applied
Field
Nonsinusoidality
accuracy
Max. Op.
Temp.
Typ. Device
Resistance
Package
400 mV/V
Full bridge
30 Oe
1.5%
125°C
625 kΩ
TDFN6
The angle sensors are typically used with a split pole magnets such as
NVE part no. 12249 or 12426.
An Evaluation Kit is available with an angle sensor, circuit board, unity-gain buffer amplifier, split-pole magnet, and a plastic magnet locating fixture.
Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.
- Part Number:
- AAT101-10E
- Quantity in Stock:
- 19880
$8.94
AB001-00E: 25 mT Sat. Gradiometer, 2.5 KOhm, RoHS MSOP
AB001-00E GMR Gradient Sensors (Gradiometers) offer unparalleled magnetic gradient
sensing. Two pairs of unshielded GMR bridge resistors provide directional sensing
of small gradients over a wide range of magnetic field strength. The devices
are sensitive only to gradients, and have low sensitivity to constant magnetic
noise.
Differential magnetic field sensor (gradiometer) --
for gear tooth, multi-pole magnet, and high noise rejection sensing.
Typ. Min. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
250
20 - 200
0.02 - 0.03
2,500 +/-20%
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) when purchasing quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
- Part Number:
- AB001-00E
- Quantity in Stock:
- 5009
$6.29
AB001-02E: 25 mT Sat. Gradiometer, 2.5 KOhm, RoHS SOIC
AB001-02E GMR Gradient Sensors (Gradiometers) offer unparalleled magnetic gradient
sensing. Two pairs of unshielded GMR bridge resistors provide directional sensing
of small gradients over a wide range of magnetic field strength. The devices
are sensitive only to gradients, and have low sensitivity to constant magnetic
noise.
Differential magnetic field sensor (gradiometer) --
for gear tooth, multi-pole magnet, and high noise rejection sensing.
Typ. Min. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Sensitivity (mV/V/Oe)
min.-max.
Resistance
(Ohms)
Package
250
20 - 200
0.02 - 0.03
2,500 +/-20%
SOIC8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 92) when purchasing quantities of 92 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
- Part Number:
- AB001-02E
- Quantity in Stock:
- 2925
$6.29
ABH001-00E: 7 mT Sat. Gradiometer, 1.2 KOhm, RoHS MSOP
ABH001-00E GMR Gradient Sensors (Gradiometers) offer unparalleled magnetic gradient sensing. Two pairs of unshielded GMR bridge resistors provide directional sensing of small gradients over a wide range of magnetic field strength. The devices are sensitive only to gradients with low sensitivity to constant external magnetic noise. This allows these sensors to operate in high noise environments, such as near electric motors or high-current wires.
Key Features:
Extremely High Sensitivity to Applied Magnetic Fields
Wheatstone Bridge Analog Output
Temperature to 150 degrees Continuous
Wide Linear Range of Operation
Near-Zero Voltage Operation
DC to >1MHz Frequency Response
MSOP Package
Applications:
General Differential Field Sensing
Gear Tooth and Encoder Speed and Position Sensing
Low Voltage, High Temperature Applications
Differential magnetic field sensor (gradiometer) --
for gear tooth, multi-pole magnet, and high noise rejection sensing.
Typ. Min. Saturation Field (Oe)
Linear Range(|Oe|)
min.-max.
Resistor
Sensitivity
(%R/Oe)
min.-max.
Resistance
(Ohms)
Package
70
5 - 40
0.06 - 0.12
1,200 +/-20%
MSOP8
(RoHS)
Note: Parts must be purchased in tube quantities (multiples of 100) when purchasing quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
This part is RoHS compliant.
- Part Number:
- ABH001-00E
- Quantity in Stock:
- 4001
$6.29
ABL004-00E: 1 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL004-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 1.0 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL004-00E
- Quantity in Stock:
- 2238
$5.19
ABL004-10E: 1 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS TDFN
NVE's ABL004-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 1.0 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL004-10E
- Quantity in Stock:
- 18259
$5.19
ABL005-00E: 0.5 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL005-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.5 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL005-00E
- Quantity in Stock:
- 9721
$5.19
ABL005-10E: 0.5 mm, 1-Bridge Analog Gear-Tooth Sensor, TDFN
NVE's ABL005-10E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.5 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.500 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL005-10E
- Quantity in Stock:
- 1604
$5.19
ABL006-00E: 0.3 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL006-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.3 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.300 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL006-00E
- Quantity in Stock:
- 771
$5.19
ABL006-10E: 0.3 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS TDFN
NVE's ABL006-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.3 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.300 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL006-10E
- Quantity in Stock:
- 9123
$5.19
ABL014-00E: 1 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL014-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 1.0 mm apart on the sensor IC, and the two sensors are phase shifted by 0.5 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm, and sensor-to-sensor phase shift is 0.500 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL014-00E
- Quantity in Stock:
- 425
$6.29
ABL014-10E: 1 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS TDFN
NVE's ABL014-10E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 1.0 mm apart on the sensor IC, and the two sensors are phase shifted by 0.5 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 1.000 mm, and phase shift from sensor to sensor is 0.500 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL014-10E
- Quantity in Stock:
- 7301
$6.29
ABL015-00E: 0.5 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL015-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.5 mm apart on the sensor IC, and the two sensors are phase shifted by 0.25 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm, and phase shift from sensor to sensor is 0.250 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL015-00E
- Quantity in Stock:
- 4709
$6.29
ABL015-10E: 0.5 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS TDFN
NVE's ABL015-10E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.5 mm apart on the sensor IC, and the two sensors are phase shifted by 0.25 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.500 mm, and phase shift from sensor to sensor is 0.250 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL015-10E
$6.29
ABL016-00E: 0.3 mm, 2-Bridge Analog Gear-Tooth Sensor, RoHS MSOP
NVE's ABL016-00E GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.3 mm apart on the sensor IC, and the two sensors are phase shifted by 0.15 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.300 mm, and phase shift from sensor to sensor is 0.150 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder MSOP8 Note: Parts must be purchased in tube quantities (multiples of 100) for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL016-00E
- Quantity in Stock:
- 491
$6.29
ABL016-10E: 0.3 mm, 2-Bridge Analog Gear-Tooth Sensor, TDFN
NVE's ABL016-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The differential sensor elements are spaced 0.3 mm apart on the sensor IC, and the two sensors are phase shifted by 0.15 mm. Bridge Resistance for Each Bridge (Ohms) Linear Range (Oersteds) Output Comments Package Dual Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center-to-center distance between sensor elements is 0.300 mm, and phase shift from sensor to sensor is 0.150 mm. 4K - 7K +/-5 to +/-100 Dual Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.
- Part Number:
- ABL016-10E
- Quantity in Stock:
- 2900
$6.29
ABT250-00E: TMR 1 mm Pitch Gear Tooth Sensor, MSOP
ABT250-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT250-00E is optimized for 1 mm pitch gears, and can be used for pitches from 0.6 to 2 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
- Part Number:
- ABT250-00E
$5.71
ABT375-00E: TMR 1.5 mm Pitch Gear Tooth Sensor, MSOP
ABT375-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT375-00E is optimized for 1.5 mm pitch gears, and can be used for pitches from 1 to 3 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
A demo board is also available.
- Part Number:
- ABT375-00E
$5.71
ABT500-00E: TMR 2 mm Pitch Gear Tooth Sensor, MSOP
ABT500-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT500-00E is optimized for 2 mm pitch gears, and can be used for pitches from 1.3 to 4 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
- Part Number:
- ABT500-00E
$5.71
ABT600-00E: TMR 2.4 mm Pitch Gear Tooth Sensor, MSOP
ABT600-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.
The ABT600-00E is optimized for 2.4 mm pitch gears, and can be used for pitches from 1.6 to 4.8 mm. The sensors have two channels to detect direction.
Key features include:
• 0.001° resolution
• Large analog peak-to-peak signals
• Operating frequency to 350 kHz
• 150 °C operating temperature
- Part Number:
- ABT600-00E
$5.71
