New Products

Displaying 101 to 120 (of 376 products)
AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board

This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040B
Quantity in Stock:
3

$19.95

AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board

This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040C

$16.95

AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board

The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040T
Quantity in Stock:
2

$19.95

AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit

The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.

The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.

Part Number:
AG903B-07E
Quantity in Stock:
9

$75.00

AG904-06: ULLGA General-Purpose PCB

A 1.2 x 0.25 inch x 0.031 inch thick (30 x 6 x 0.75 mm) PCB for demonstrating 1.1 x 1.1 mm ULLGA4 sensors (-14E sensor suffix; order sensors separately).

Note that since these boards use very small sensors, they require reflow or hot-air soldering techniques.

Part Number:
AG904-06
Quantity in Stock:
546

$5.00

AG905-07E: ALT025 High Current PCB Demonstration

This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.

Part Number:
AG905-07E
Quantity in Stock:
8

$75.00

AG910-07E: GMR Switch Evaluation Kit w/ZIF socket

AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.

Part Number:
AG910-07E
Quantity in Stock:
9

$90.00

AG911-07E: GMR Switch Evaluation Kit

AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.

Part Number:
AG911-07E
Quantity in Stock:
11

$65.00

AG915-06: MSOP8 Printed Circuit Board (0.25" octagonal)

A 0.25-inch (6 mm) octagonal PCB for easy connections to MSOP8 sensors (-00E suffix; order sensors separately).

The PCB provides through holes for #28 or #30 wires.

Part Number:
AG915-06
Quantity in Stock:
511

$2.25

AG918-06: MSOP8 Printed Circuit Board (2" x 0.25")

A 2 x 0.25 inch (50 x 6 mm) PCB designed to be used with MSOP8 sensors (-00E package; purchase sensors separately).

This PCB is also included in the AG910-07 and AG911-07 Sensor Evaluation Kits.

Part Number:
AG918-06
Quantity in Stock:
575

$4.25

AG919-06: MSOP8 PCB (2" x 0.25"; cross-axis orientation)

The AG919-06 is a 2 x 0.25 inch (50 x 6 mm) PCB designed to be used with MSOP8 sensors (-00E package; order sensors separately). The MSOP8 is rotated 90 degrees compared to the AG918-06.

Part Number:
AG919-06
Quantity in Stock:
5

$4.25

AG920-07E: GT Sensor Evaluation Kit

The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.

Part Number:
AG920-07E
Quantity in Stock:
16

$65.00

AG921-07E: AKL001 Gear-Tooth Sensor Demonstrator

A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".

Part Number:
AG921-07E
Quantity in Stock:
3

$90.00

AG930-07E: AAT001 1.25 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.

Part Number:
AG930-07E
Quantity in Stock:
10

$75.00

AG931-07E: AAT003 40 KOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.

Part Number:
AG931-07E
Quantity in Stock:
11

$75.00

AG932-07E: ADT002 Rotation Sensor Evaluation Kit

The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.

Part Number:
AG932-07E
Quantity in Stock:
3

$90.00

AG933-07E: AAT009 6 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.

Part Number:
AG933-07E
Quantity in Stock:
7

$75.00

AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.

Part Number:
AG934-07E
Quantity in Stock:
6

$75.00

AG935-07E: 60-LED "Blinky" AAT003 Angle Sensor Demo Board

This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller. The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration. A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included. The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.

Part Number:
AG935-07E
Quantity in Stock:
3

$150.00

AG940-07E: Digital/Analog/Omnipolar/Bipolar Sensor Demo Board

The kit includes a demo board with our most popular sensor types: digital, analog, omnipolar, and bipolar. Each sensor drives an indicator LED. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by two coin cells (included).

Part Number:
AG940-07E
Quantity in Stock:
5

$75.00

Displaying 101 to 120 (of 376 products)