New Products
ALT026-10E-EVB01: 0-20 mT DFN6 TMR magnetometor eval board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT026-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
- Part Number:
- ALT026-10E-EVB01
$19.95
ALT026-10E: 0-20 mT TMR Bipolar Analog Sensor, 20 KOhm, x-axis, TDFN6
The ALT026 is a Tunneling Magnetoresistance (TMR) analog bridge magnetic sensor with extraordinary signal amplitude and wide linear range. The differential bridge output is bipolar, meaning it is positive for a positive field and negative for an opposite field polarity. The ALT025 has cross-axis sensitivity (across the pads). Features: Large signal (200 mV/V) Wheatstone bridge magnetometer configuration 0 - 10 V power supply 20 kiloohm device resistance for low power ±20 mT (±200 Oe) linear range High linearity output (
- Part Number:
- ALT026-10E
$12.00
ILDC11V-15-01: 3.3-to-3.3V DFN6 DC-DC Conv Eval Board
These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC
convertor, bypass capacitors as recommended, as well as test pads, screw terminals, provisions for header pins. LEDs that show the DC-to-DC convertor is operating.
The boards follow best practices including 2s2p with thermal vias for optimal thermal
performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.
The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate
fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.
- Part Number:
- ILDC15V-15-01
$84.95
ASR022-10E-EVB01: ABZ TMR Smart Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR022-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an encoder-compatible ABZ interface.
- Part Number:
- ASR022-10E-EVB01
- Quantity in Stock:
- 30
$19.95
ASR012-10E-EVB01: I2C TMR Smart Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR012-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface.
- Part Number:
- ASR012-10E-EVB01
- Quantity in Stock:
- 30
$19.95
ASR002-10E-EVB01: SPI TMR Smart Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR002-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use SPI interface.
- Part Number:
- ASR002-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AAT101-10E-EVB01: Full-Bridge TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
- Part Number:
- AAT101-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AAT009-10E-EVB01: 6 MOhm TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
- Part Number:
- AAT009-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AAT006-10E-EVB01: 1.5 mT TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
- Part Number:
- AAT006-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AAT003-10E-EVB01: 40 kOhm TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
- Part Number:
- AAT003-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AAT001-10E-EVB01: 1.25 MOhm TDFN6 TMR Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
- Part Number:
- AAT001-10E-EVB01
- Quantity in Stock:
- 30
$19.95
ADL922-14E: 4 mT, 3V Nanopower GMR Switch, DFN4
NVE's ADL922-14E Ultraminiature Nanopower Switch integrates GMR sensor elements with onboard digital signal processing. Continuous operation allows high frequency switching. External duty cycling allows nanopower operation. The part is packaged in a 1.1 x 1.1 x 0.35 mm DFN4 package. Features: Precise 4 mT operate point Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm DFN4 package 2.4 to 4.2 V Typical Power Consumption 84 microwatts at 2.4 V without duty-cycling 100 kHz Operating Frequency Digital Switch Output Applications: Battery-Powered Devices Wearables and IoT Sensors Battery-Powered Devices Industrial Sensors
- Part Number:
- ADL922-14E
- Quantity in Stock:
- 2935
$5.63
IL715V-01: 4-Ch (all same dir) Wide-Body 7 kV Isolator Eval Bd
These 2 x 3.5-inch (50 x 90 mm) boards have an IL715VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
- Part Number:
- IL715V-01
- Quantity in Stock:
- 50
$49.95
IL7614V-01: Isolated 3-Ch SPI w/Integ DC-DC Conv Eval Board
This Evaluation Board provides a complete isolated three-channel SPI node, plus an isolated 3.3 V to 3.3 V DC-to-DC convertor using an IL7614VE. It is ideal for half-duplex SPI applications.
These 2 x 3.5-inch (50 x 90 mm) boards also include screw terminal and test pads, and uses a 2s2p board with vias for optimal thermal performance. LEDs indicate DC-to-DC convertor input and output power.
The IL7614V is a high-speed, fully-isolated, data couplers with an integrated, one-quarter watt 3.3 V-to-3.3 V DC-to-DC convertor. This level of integration dramatically reduces chip count and board area.
- Part Number:
- IL7614V-01
$84.95
ILDC13V-15E: Isolated 1/4W 3.3-to-6V DC-DC Conv, 2.5 kV, DFN6
The ILDC13V-15E is a one-quarter watt fully-regulated 3.3V-to-6V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The "V" suffix indicates an extended creepage package and full 2.5 kV isolation.
The part can be used to power high-side gate supplies in H-bridges.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide virtually unlimited barrier life.
- Part Number:
- ILDC13V-15E
$5.43
ILDC12V-15E: Isolated 1/4W 3.3-to-5V DC-DC Conv, 2.5kV
The ILDC12-15E is a one-quarter watt fully-regulated 3.3V-to-5V DC-DC boost convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The "V" suffix indicates an extended creepage package and full 2.5 kV isolation.
The part can be used to generate isolated RS-485 bus supplies or to power high-side gate supplies in H-bridges.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide virtually unlimited barrier life.
- Part Number:
- ILDC12V-15E
$5.43
IL717V-01: 4-Ch (3/1 dir) Wide-Body 7 kV Isolator Eval Bd
These 2 x 3.5-inch (50 x 90 mm) boards have an IL717VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
- Part Number:
- IL717V-01
$49.95
IL716V-01: 4-Ch (2 ea dir) Wide-Body 7 kV Isolator Eval Bd
These 2 x 3.5-inch (50 x 90 mm) boards have an IL716VE isolator, two bypass capacitors as recommended, screw connections, test pads, and provisions for header pins.
V-Series isolators are rated at a best-in-class 7 kVrms (9.9 kVpeak) isolation voltage. The evaluation board demonstrates best practice for maintaining 8 millimeter creepage. The isolators are conformally-coated to minimize arcing around the part.
- Part Number:
- IL716V-01
$49.95
ILDC11V-15E: 1/4W 3.3-to-3.3V DC-DC Conv, 2.5 kV, DFN6
The ILDC11V-15E is an ultraminiature, one-quarter watt fully-regulated 3.3V-to-3.3V DC-DC convertor in an ultraminiature 3 mm x 5.5 mm DFN6 package. The "V" suffix indicates an extended creepage package and full 2.5 kV isolation.
The part can be used to generate isolated RS-485 bus supplies or isolated analog supplies for ADC and DAC circuits.
The device minimizes board space and parts count, requiring just three external capacitors. No additional regulation is required and there is no minimum load.
Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.
A high-temperature process allows up to 175 °C junction temperature for full power up to 125 °C operating temperature with no derating. Integrated short-circuit protection avoids excessive power dissipation.
NVE’s proven IsoLoop® isolation technology and a unique ceramic/polymer composite barrier provide virtually unlimited barrier life.
- Part Number:
- ILDC11V-15E
$5.98
ADK991-14E: 350 mT, 3V Nanopower TMR Switch, ULLGA
The ADK991-14E Nanopower Switch integrates TMR sensor elements with digital signal processing. Continuous operation allows high frequency switching. The part is packaged in an ultraminiature ULLGA. Features: 350 mT Digital Switch Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package 2.4 to 4.2 V 1 microamp quiescent current at 3 V without duty-cycling Ultraminiature 1.1 mm x 1.1 mm x 0.35 mm ULLGA package Applications: MRI Detection Battery-Powered Devices Portable Instruments Wearables
- Part Number:
- ADK991-14E
- Quantity in Stock:
- 5
$17.05
