Sensor Evaluation Kits

Displaying 1 to 50 (of 50 products)
AAH002-02E PCBA: Ultrahigh Sensitivity Analog Sensor Assembly

A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.

Part Number:
AAH002-02E PCBA
Quantity in Stock:
27

$150.00

AG001-01E: GMR Analog Sensor Evaluation Kit

The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.

Part Number:
AG001-01E
Quantity in Stock:
2

$60.00

AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board

This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040B
Quantity in Stock:
31

$19.95

AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board

This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040C
Quantity in Stock:
27

$16.95

AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board

The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040T

$19.95

AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit

The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.

The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.

Part Number:
AG903B-07E
Quantity in Stock:
2

$75.00

AG905-07E: ALT025 High Current PCB Demonstration

This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.

Part Number:
AG905-07E

$75.00

AG910-07E: GMR Switch Evaluation Kit w/ZIF socket

AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.

Part Number:
AG910-07E
Quantity in Stock:
10

$90.00

AG911-07E: GMR Switch Evaluation Kit

AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.

Part Number:
AG911-07E
Quantity in Stock:
11

$65.00

AG920-07E: GT Sensor Evaluation Kit

The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.

Part Number:
AG920-07E
Quantity in Stock:
8

$65.00

AG921-07E: AKL001 Gear-Tooth Sensor Demonstrator

A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".

Part Number:
AG921-07E

$90.00

AG930-07E: AAT001 1.25 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.

Part Number:
AG930-07E
Quantity in Stock:
19

$70.00

AG931-07E: AAT003 40 KOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.

Part Number:
AG931-07E
Quantity in Stock:
22

$75.00

AG932-07E: ADT002 Rotation Sensor Evaluation Kit

The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.

Part Number:
AG932-07E
Quantity in Stock:
11

$90.00

AG933-07E: AAT009 6 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.

Part Number:
AG933-07E

$75.00

AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.

Part Number:
AG934-07E
Quantity in Stock:
1

$75.00

AG935-07E: 60-LED "Blinky" AAT003 Angle Sensor Demo Board

This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller. The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration. A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included. The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.

Part Number:
AG935-07E
Quantity in Stock:
2

$150.00

AG941-07E: ADL-Series Sensor Demo Board

The kit includes a demo board with three ultraminiature, ultralow-power ADL-Series magnetic sensors. Each sensor drives an indicator LED, and a meter shows the sensor power in microamps or nanoamps. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by a coin cell (included).

Part Number:
AG941-07E
Quantity in Stock:
3

$90.00

AG951-07E: SM324-10E Smart TMR Magnetometer Evaluation Kit

The AG951-07 Evaluation Kit has everything you need to calibrate, test, and evaluate the remarkable SM324-10E Smart TMR Magnetometer. The kit includes:
    • An evaluation board with:
          - an SM324-10E sensor.
          - a microcontroller connected to the sensor via I²C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • A powerful, intuitive graphical user interface.
    • Simple software installation.
    • Flexibility to power from USB or an external power supply.
    • Isolated USB interface for safety and noise minimization.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG951-07E
Quantity in Stock:
21

$245.00

AG952-07E: SM124-10E Smart GMR Magnetometer Evaluation Kit

The AG952-07 Evaluation Kit has everything you need to calibrate, test, and evaluate the easy-to-use SM124-10E Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM124-10E sensor.
          - a microcontroller connected to the sensor via I²C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG952-07E
Quantity in Stock:
10

$95.00

AG953-07E: SM225-10E Smart TMR Magnetometer Evaluation Kit

The AG953-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM225-10E Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM225-10E sensor.
          - a microcontroller connected to the sensor via SPI.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG953-07E
Quantity in Stock:
3

$95.00

AG953H-07E: SM225-10E Bussbar Current Sensor Demonstration

The AG953H-07 demonstrates high current measurement with the SM225-10E Smart TMR Magnetometer. A 1/4" x 1/2" busbar is mounted to the PCB, and the sensor can detect up to +/-650 amps. Based on the AG953-07E Evaluation Kit, a powerful, intuitive graphical user interface allows the user to control sensor offset, calibration, filtering, and memory.

Part Number:
AG953H-07E
Quantity in Stock:
2

$129.00

AG954-07E: TDFN6 Socket Board

The AG954-07E provides a socket for easy programming and prototyping of TDFN6 devices without soldering and unsoldering.

The custom socket is compatible with NVE's 2.5 mm x 2.5 mm TDFN6 package parts (-10E suffixes).

The board is 1.5" x 2" (38 mm x 50 mm), and uses brass hardware to minimize magnetic interference with the socketed sensor.
A 0.1"-spaced header provides for connections to the sensors, and a row of 0.1"-spaced through-holes allows for auxiliary parts such as a decoupling capacitor or an LED.

Part Number:
AG954-07E

$129.00

AG955-07E: Self-Contained SM12x Programmer

This self-contained module allows zeroing and programming the digital output threshold and hysteresis or SM124-10E or SM125-10E Smart Magnetometer without need of a computer or a customer microcontroller.

The 2.5" x 2.5" (64 mm x 64 mm) board has an I²C master microcontroller connected to the SM124.

A pushbutton for zeros the sensor, and miniature rotary thumbwheel switches provide three digits of resolution for the threshold and two for hysteresis. A custom TDFN-6 socket accommodates the 2.5 mm x 2.5 mm SM12x-10E. The module is powered by a small wall-mounted power supply (included).

Jumpers allow the sensor to be disconnected from the rest of the board so the board can be used as an interface to the customer’s electronics.

This module includes:

    • A 2.5 x 2.5 mm TDFN6 socket for a SM12x-10E Smart Magnetometer

    • A preprogrammed, onboard microcontroller

    • Two sets of thumbwheel switches for digital threshold and hysteresis

    • Two LEDs indicating the sensor’s output and successful programming

    • A 5-volt wall-mount power supply

Sensors are sold separately.

Part Number:
AG955-07E

$195.00

AG956-07E: ASR002-10E Smart SPI Angle Sensor Evaluation Kit

The AG956-07 Evaluation Kit has everything you need to calibrate, test, and evaluate the remarkable ASR002-10E Smart Angle Sensor. The kit includes:
    • An evaluation board with:
          - an ASR002-10E sensor
          - a diametrical magnet
          - magnet fixturing and a

    • An interface board with:
          - a microcontroller connected to the sensor via SPI
          - flexibility to power from USB or external power supply
          - isolated USB interface for safety and low noise.

    • A powerful, intuitive graphical user interface.

    • Simple software installation.

    • USB cable to connect the Evaluation Board to a computer.

Part Number:
AG956-07E
Quantity in Stock:
32

$195.00

AG957-07E: ASR002 Smart TMR Angle Sensor breakout board

The AG957-07E provides easy connections to an ASR002-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG957-07E
Quantity in Stock:
2

$19.95

AG958-07E: SM124 Smart GMR Magnetometer breakout board w/connector

The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG958-07E
Quantity in Stock:
9

$24.95

AG959-07E: SM225 High-Speed Smart TMR Magnetometer breakout board

The AG959-07E provides easy connections to an SM225-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG959-07E
Quantity in Stock:
5

$19.95

AG960-07E: SM324 Ultraprecise Smart Magnetometer breakout board

The AG960-07E provides easy connections to an SM324-10E Precision TMR Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG960-07E
Quantity in Stock:
6

$19.95

AG961-07E: SM125 Smart GMR Magnetometer breakout board w/connector

The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG961-07E
Quantity in Stock:
22

$24.95

AG962-07E: SM125-10E Smart GMR Magnetometer Evaluation Kit

The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM125-10E sensor.
          - a microcontroller connected to the sensor via I²C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG962-07E
Quantity in Stock:
4

$95.00

AG963-07E: ASR012-10E I²C Smart Angle Sensor Evaluation Kit

The AG963-07E Evaluation Kit has everything you need to calibrate, test, and evaluate the remarkable ASR012-10E I2C Smart Angle Sensor. The kit includes:
    • An evaluation board with:
          - an ASR012-10E sensor
          - a diametrical magnet
          - magnet fixturing

    • An interface board with:
          - a microcontroller connected to the sensor via I²C
          - flexibility to power from USB or external power supply
          - isolated USB interface for safety and low noise.

    • A powerful, intuitive graphical user interface.

    • Simple software installation.

    • USB cable to connect the Evaluation Board to a computer.

Part Number:
AG963-07E
Quantity in Stock:
5

$195.00

AG964-07E: ASR022-10E ABZ TMR Encoder Sensor Demo Kit

The AG964-07E Demonstation Board has everything you need to evaluate the remarkable ASR022-10E ABZ TMR Encoder Sensor. The demonstration includes:
    • ASR022-10E ABZ Noncontact TMR Encoder Sensor
    • A four-digit display to indicate rotation
    • Part # 12426 split-pole Alnico 5 round horseshoe magnet
    • LEDs for A, B, Z, and Direction outputs
    • Plastic magnet locating fixture
    • Powered by two AAA batteries (included)

Part Number:
AG964-07E
Quantity in Stock:
2

$195.00

AG965-07E: AET500-02E TMR Linear Sensor Demo Kit

The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor. The kit includes:
  • A 3 x 5-inch (76 x 127 mm) PCB   • An AET500-02E 5 mm pole-pitch sensor
  • A four digit position display
  • Part #12592 5mm pole pitch magnetic tape
  • 3-D printed fixturing
  • LEDs for pole detected
  • Powered by three AAA batteries (included)

Part Number:
AG965-07E
Quantity in Stock:
20

$195.00

AG966-07E: ASR012 I2C/PWM Smart TMR Angle Sensor breakout board

The AG966-07E provides easy connections to an ASR012-10E I2C/PWM TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG966-07E
Quantity in Stock:
2

$19.95

AG967-07E: ASR022 ABZ Smart TMR Encoder Sensor breakout board

The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG967-07E
Quantity in Stock:
14

$19.95

AG968-07E: SM228 15 mT I2C Smart TMR Magnetometer Breakout Board

The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG968-07E
Quantity in Stock:
1

$19.95

AG969-07E: SM228-10E Smart I²C TMR Magnetometer Evaluation Kit

The AG969-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM228-10E sensor.
          - a microcontroller connected to the sensor via I2C.
          - a bus-bar for evaluating as a current sensor.
    • An LED indicating the state of the threshold output.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG969-07E
Quantity in Stock:
4

$95.00

AG970-07E: AET-Series TMR Linear Sensor Eval Kit

The AG970-07E Evaluation Kit helps test a variety AET-Series sensors with linear magnetic scales. The kit includes:   • All five AET-Series parts (unsoldered in tubes)
  • A 3 x 4-inch (76 x 101 mm) PCB with test points and screw terminals
  • Detachable fixturing for linear magnetic tape (tape sold separately)

Part Number:
AG970-07E

$65.00

AG972-07E: ABT375 TMR Gear-Tooth Sensor Demo Kit

The AG972-07E Demonstration Board showcases rotational encoding to a few thousandths of a degree with an ABT375-00E sensor and a 30-tooth gear.

The kit includes:
  • A 3 x 5-inch (76 x 127 mm) PCB
  • An ABT375-00E gear tooth sensor
  • An eight-digit rotational display
  • a 30-tooth. 0.5 module gear
  • Part #12216 ceramic bias magnet
  • Test points for analog outputs
  • Powered by two AAA batteries (included)

Part Number:
AG972-07E
Quantity in Stock:
1

$195.00

AG973-07E: SM223-10E Smart I²C TMR Magnetometer Evaluation Kit

The AG973-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM228-10E sensor.
          - a microcontroller connected to the sensor via I2C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • An LED indicating the state of the threshold output.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG973-07E
Quantity in Stock:
7

$95.00

AG974-07E: ACT001-10E Isolated Current Sensor Evaluation Board

This 2” x 2” square evaluation board allows you to test the remarkable ACT001-10E current sensor and a common application circuit.

The ACT001-10E is a fully-isolated, inline current sensor with an on-chip current strap. A Wheatstone bridge manufactured with NVE’s state-of-the-art tunneling magnetoresistance (TMR) sensor elements detects the magnetic field from the input current across NVE’s unique polymer isolation barrier.

Part Number:
AG974-07E
Quantity in Stock:
19

$50.00

AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board

The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG975-07E

$19.95

AG976-07E: ASR003-10E Smart SPI Angle Sensor Evaluation Kit

The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.

Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.

Part Number:
AG976-07E

$195.00

AG977-07E: ASR003 Smart TMR Angle Sensor breakout board

The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG977-07E
Quantity in Stock:
4

$19.95

ALT021-10E-EVB01: 0-0.25 mT TMR magnetometor eval board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.

Part Number:
ALT021-10E-EVB01
Quantity in Stock:
41

$19.95

ALT021-10E-EVB02: 0-0.25 mT TMR eval board w/amplifier

A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.

The board can be powered by a 0.9 to 7 V power supply or battery and provides a linear, single-ended output.

Part Number:
ALT021-10E-EVB02
Quantity in Stock:
39

$49.95

ALT023-10E-EVB01: 0-1 mT TMR magnetometor eval board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.

Part Number:
ALT023-10E-EVB01
Quantity in Stock:
61

$19.95

ALT025-10E-EVB01: 0-10 mT DFN6 TMR magnetometor eval board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.

Part Number:
ALT025-10E-EVB01
Quantity in Stock:
19

$19.95

ALT025-14E-EVB01: 0-10 mT DFN4 TMR magnetometor eval board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.

Part Number:
ALT025-14E-EVB01
Quantity in Stock:
4

$19.95

Displaying 1 to 50 (of 50 products)