Power Eval Boards

Displaying 1 to 13 (of 13 products)
AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit

The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.

The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.

Part Number:
AG903B-07E
Quantity in Stock:
1

$75.00

AG905-07E: ALT025 High Current PCB Demonstration

This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.

Part Number:
AG905-07E

$75.00

AG953H-07E: SM225-10E Bussbar Current Sensor Demonstration

The AG953H-07 demonstrates high current measurement with the SM225-10E Smart TMR Magnetometer. A 1/4" x 1/2" busbar is mounted to the PCB, and the sensor can detect up to +/-650 amps. Based on the AG953-07E Evaluation Kit, a powerful, intuitive graphical user interface allows the user to control sensor offset, calibration, filtering, and memory.

Part Number:
AG953H-07E
Quantity in Stock:
1

$129.00

ILDC11-01: Ultraminiature Isolated 3.3-to-3.3V DC-DC Conv Eval Bd (OBS)

This Evaluation Board uses the 3.3-to-3.3V version of the world’s smallest isolated DC-to-DC convertor, the ILDC11-15E.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC11-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC11 is an ultraminiature one-quarter watt DC-to-DC convertor with 2.5 kV isolation that can be used to generate an isolated 3.3-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC11-01
Quantity in Stock:
50

$49.95

ILDC11V-01: Isolated 3.3-to-3.3V SOIC16 DC-DC Conv Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating.

The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.

The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC11V-01
Quantity in Stock:
50

$84.95

ILDC11V-15-01: 3.3-to-3.3V DFN6 DC-DC Conv Eval Board

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating.

The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.

The ILDC1xV-15 Series are ultraminiature one-quarter watt DC-to-DC convertors that generate independent outputs with 2.5 kV isolation from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC15V-15-01
Quantity in Stock:
50

$84.95

ILDC12V-01: Isolated 3.3-to-5V SOIC16 DC-DC Conv Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating. The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired. The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC12V-01
Quantity in Stock:
50

$84.95

ILDC12V-15-01: Isolated 3.3-to-5V DFN6 DC-DC Conv Eval Bd

This Evaluation Board uses the 3.3-to-5 V version of world’s smallest isolated DC-to-DC convertor, the ILDC12-15E.

The 1.75 by 1.75 inch (45 by 45 mm) board has an ILDC12-15E plus the three required external bypass capacitors as well as LEDs to show the DC-to-DC convertor is operating. Screw terminals provide easy connections.

The ILDC12V-15E is an ultraminiature one-quarter watt DC-to-DC boost convertor with 2.5 kV isolation that can be used to generate an isolated five-volt bus supply from a 3.3-volt controller supply.

No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads are not necessary for EMI mitigation.

Part Number:
ILDC12V-15-01
Quantity in Stock:
50

$84.95

ILDC13V-01: Isolated 3.3-to-6V SOIC16 DC-DC Conv Eval Bd

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, and header pins. LEDs that show the DC-to-DC convertor is operating. The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired. The ILDC1x-Series are ultraminiature one-quarter watt DC-to-DC convertors that generate fully-isolated, independent outputs from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC13V-01
Quantity in Stock:
50

$84.95

ILDC13V-15-01: 3.3-to-6V DFN6 DC-DC Conv Eval Board

These 2 x 3.5-inch (50 x 90 mm) boards contain your choice of ILDC1x-Series DC-to-DC convertor, bypass capacitors as recommended, as well as test pads, screw terminals, provisions for header pins. LEDs that show the DC-to-DC convertor is operating.

The boards follow best practices including 2s2p with thermal vias for optimal thermal performance, and stitched ground planes to provide CISPR 32-compliant EMC mitigation with no external components. The boards have provisions for external components if additional EMC mitigation is desired.

The ILDC1xV-15 Series are ultraminiature one-quarter watt DC-to-DC convertors that generate independent outputs with 2.5 kV isolation from a 3.3-volt supply. 3.3, 5, and 6-volt output versions are available. No additional regulation is required and there is no minimum load. Frequency hopping and shielding reduce EMI, and ferrite beads or other external components are generally not necessary for EMI mitigation.

Part Number:
ILDC13V-15-01
Quantity in Stock:
50

$84.95

SHIELD01-01: 40V/50A H-Bridge Arduino Shield Eval Board

This Arduino Shield board implements an H-bridge power converter using four power MOSFETs, four IL610CMTI-1E ultrahigh CMTI isolated MOSFET drivers, and two ILDC13-15E ultraminiature isolated DC-to-DC convertors.

The board is rated for 40 volts and 50 amps, to control up to two-kilowatt loads.

Example programs are available via our GitHub Repository.

Key features of the board are:
  • A Simple three-wire Arduino interface (PWM, Dir, and Enable)
  • Heat-sinking and thermal vias
  • Standard Arduino Shield form factor outline
  • Easy connections with large screw terminals

Specifications:
  • Max. load: 2 kW (40 V / 50 A)
  • Load supply line: 8 to 40 V
  • Arduino input supply: 5V or 7 V to 20 V, 500 mA max.
  • Logic-to-load isolation: 2.5 kV per UL 1577
  • Operating Temperature Range: -40 °C to 85 °C
  • Dimensions: 2.1 in. by 2.7 in. (53.4 mm by 68.6 mm)

Applications:
  • Motor speed and direction control
  • Robotics
  • DC-to-AC invertors

Part Number:
SHIELD01-01
Quantity in Stock:
17

$195.95

SMPS1-01: IL711/IL610 MSOP Isolated 2.5W SMPS Demo Board

This board demonstrates an isolated, high-efficiency synchronous buck converter switch-mode power supply (SMPS) using the world’s smallest isolators, NVE IsoLoop® MSOP Isolators.

The output is 3.3V at 750 mA.

The board has three channels of isolation to ensure the output is electrically isolated from the input. A two-channel MSOP-8 isolator isolates synchronous rectification and a single-channel, failsafe, MSOP-8 isolator isolates output-voltage feedback. MSOP isolators minimize board area.

Despite the compact components, the board has 1.2 kV isolation and maintains 3 mm creepage.

Board dimensions are approx. 2 in. by 0.5 in.

Part Number:
SMPS1-01
Quantity in Stock:
6

$199.95

SMPS2-01: 2.5 kV MSOP Isolated 2.5W SMPS Demo Board

This board demonstrates an isolated, high-efficiency synchronous buck converter switch-mode power supply (SMPS) using the world’s smallest isolators, NVE IsoLoop® MSOP Isolators.

The output is 3.3V at 750 mA.

The board has three channels of isolation to ensure the output is electrically isolated from the input. A two-channel MSOP-8 isolator isolates synchronous rectification and a single-channel MSOP-8 isolator isolates output-voltage feedback. MSOP isolators minimize board area.

Despite the compact components, the board has full 2.5 kV isolation and maintains 3 mm creepage.

Board dimensions are approx. 2 in. by 0.5 in.

Part Number:
SMPS2-01
Quantity in Stock:
8

$199.95

Displaying 1 to 13 (of 13 products)