Gear and Rotational Sensors

Displaying 21 to 26 (of 26 products)
ABL006-10E: 0.3 mm, 1-Bridge Analog Gear-Tooth Sensor, RoHS TDFN

NVE's ABL006-10 GMR sensor is an analog output sensor for gear tooth sensing or magnetic encoders. The part features differential sensor elements spaced 0.3 mm apart on the sensor IC arranged in a full bridge configuration. Bridge Resistance (Ohms) Linear Range (Oersteds) Output Comments Package Differential Sensor (Gradiometer); senses the magnetic field gradient across the sensor IC. Center to center distance between sensor elements is 0.300 mm. 4K - 7K +/-5 to +/-100 Analog Bridge Gear Tooth or Encoder TDFN6 Note: Parts must be purchased in multiples of 100 for quantities of 100 or more. Larger quantities are subject to NVE's standard lead times.

Part Number:
ABL006-10E
Quantity in Stock:
187

$5.19

AET120F-00E: 1.2 mm, Full-Bridge TMR Rotational / Linear Sensor, MSOP

AET120F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.

The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.

Evaluation and Demonstration Kits are also available.

Part Number:
AET120F-00E
Quantity in Stock:
123

$6.88

ABT600-00E: TMR 2.4 mm Pitch Gear Tooth Sensor, MSOP

ABT600-00E gear-tooth sensors are typically used with back-biasing magnets to encode the position of a ferrous gear.

The ABT600-00E is optimized for 2.4 mm pitch gears, and can be used for pitches from 1.6 to 4.8 mm. The sensors have two channels to detect direction.

Key features include:
   • 0.001° resolution
   • Large analog peak-to-peak signals
   • Operating frequency to 350 kHz
   • 150 °C operating temperature

Part Number:
ABT600-00E

$6.88

ADT002-10E: Low Hysteresis, Ultralow Power Rotation Quadrant Sensor, TDFN6

ADT002-10E Rotation Sensors provide two binary digital outputs to accurately indicate the absolute rotational quadrant of a rotating magnet. The two outputs are 90 degrees out of phase to also provide directional information. An additional output indicates a fault if the magnetic field is too high. The ADT002 is low hysteresis to provide accurate, absolute rotational quadrant information. The sensors use NVE’s unique Tunneling Magnetoresistance (TMR) technology to minimize power consumption and size. The sensors are typically used with radially-magnetized disk magnets or split pole magnet. An Evaluation Kit is available with an angle sensor, magnet, circuit board with indicator LEDs, and a plastic magnet locating fixture. Note: Please purchase in increments of 100 when purchasing quantities of 100 or more.

Part Number:
ADT002-10E

$7.15

AET100F-00E: 1 mm, Full-Bridge TMR Rotational / Linear Sensor, MSOP

AET100F-00E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.

The full-bridge configuration maximizes noise immunity and provides large 600 mVpp/V output signals. Sine and cosine outputs provide direction information.

Evaluation and Demonstration Kits are also available.

Part Number:
AET100F-00E

$6.88

AET500-02E: 5 mm, Half-Bridge TMR Rotational / Linear Sensor, SOIC

AET500-02E sensors can be used with multipole ring magnets as rotary encoders or with magnetic scale tapes as linear motion sensors. High sensitivity allows for wide airgaps and accommodates mechanical tolerances.

The half-bridge configuration maximizes noise immunity and provides large 300 mVpp/V output signals. Sine and cosine outputs provide direction information.

Evaluation and Demonstration Kits are also available.

Part Number:
AET500-02E

$5.67

Displaying 21 to 26 (of 26 products)